MEGAsquirt A place to collectively sort out this megasquirt gizmo

INJ outputs not working on DIYPnP

Old 01-08-2011, 12:08 AM
  #1  
Junior Member
Thread Starter
 
JustinHoMi's Avatar
 
Join Date: Jul 2005
Location: Hillsborough, NC
Posts: 273
Total Cats: 1
Default INJ outputs not working on DIYPnP

I just built a DIYPnP for a 1.6 miata. Hopefully this is just an ID-10T error on my part, but I suspect that the microsquirt module is defective.

Two issues when running it on the JimStim:

1. The O2 sensor is reading 0.28 volts in megatune regardless of the output voltage from the jimstim.

2. Neither INJ output is working (INJ1, INJ2). Jimstim INJ LED's don't light up. Multimeter confirms 0v on both outputs.

All other functions work in TunerStudio... it's sync'd up and displays the RPM and PW... so the injectors should be firing. Jimstim is confirmed working with another megasquirt.

I built it per the 90-93 instructions. I only included the 5v circuit, high side driver, the 2 pullups (R3, R4), and the iac flyback diode (R5). It's wired per the spreadsheet.

I put 3.0.3t on there and loaded DIY's default config.

Any thoughts before I email DIY?
JustinHoMi is offline  
Old 01-10-2011, 02:07 PM
  #2  
Newb
 
zuki_dan's Avatar
 
Join Date: Mar 2010
Posts: 8
Total Cats: 0
Default

I have been in communication with matt at diyautotune. Trying to resolve a similar issue. I have the whole thing built with sequential ignition and injection. I have all circuits working on with the Jim Stim except the INJ2 circuit. The LED for this output just glows dimmly when power is applied. Under realtime display in tunerstudio the circuit just sits at 0, while the INJ1 circuit is pulsing between 1 & 0.
zuki_dan is offline  
Old 01-10-2011, 02:09 PM
  #3  
Boost Czar
iTrader: (62)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,488
Total Cats: 4,077
Default

how are you using the JimStim on a DIYPNP?

pic of the board please, both sides.
Braineack is offline  
Old 01-10-2011, 02:13 PM
  #4  
Newb
 
zuki_dan's Avatar
 
Join Date: Mar 2010
Posts: 8
Total Cats: 0
Default

I am using the Jim Stim with a spare ecm pigtail I had purchased and wired in with the screw in connections.
zuki_dan is offline  
Old 01-10-2011, 02:26 PM
  #5  
Junior Member
Thread Starter
 
JustinHoMi's Avatar
 
Join Date: Jul 2005
Location: Hillsborough, NC
Posts: 273
Total Cats: 1
Default

In my case it was just an oversight. I forgot that you have to supply the Jimstim with 5v. I've been doing it the same way for so long (using afm signal), that I forgot that I was drawing the 5v for the jimstim from the afm's vref.
JustinHoMi is offline  
Old 01-10-2011, 02:30 PM
  #6  
Newb
 
zuki_dan's Avatar
 
Join Date: Mar 2010
Posts: 8
Total Cats: 0
Default

pics of the Jim Stim.
Attached Thumbnails INJ outputs not working on DIYPnP-jim-stim-001-640x471-.jpg   INJ outputs not working on DIYPnP-jim-stim-002-640x467-.jpg  
zuki_dan is offline  
Old 01-10-2011, 02:35 PM
  #7  
Newb
 
zuki_dan's Avatar
 
Join Date: Mar 2010
Posts: 8
Total Cats: 0
Default

pics of diypnp
Attached Thumbnails INJ outputs not working on DIYPnP-dscn4602-640x480-.jpg   INJ outputs not working on DIYPnP-dscn4603-640x480-.jpg  
zuki_dan is offline  
Old 01-10-2011, 03:48 PM
  #8  
Boost Czar
iTrader: (62)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,488
Total Cats: 4,077
Default

zuki, see no reason they wouldn't work through a quick visual scan.
Braineack is offline  
Old 01-10-2011, 05:04 PM
  #9  
Newb
 
zuki_dan's Avatar
 
Join Date: Mar 2010
Posts: 8
Total Cats: 0
Default

Yeah I have been talking back and forth with matt at diyautotune and don't seem to be getting anywhere with getting the problem fixed. I have tried different firmwares and making a tune from scratch, even using 2 injection events and the same thing happens every time. I am currently using 303y firmware.

Any help would be greatly appreciated.
zuki_dan is offline  
Old 01-10-2011, 05:36 PM
  #10  
Elite Member
iTrader: (16)
 
99mx5's Avatar
 
Join Date: Oct 2006
Location: Las Cruces, NM
Posts: 1,647
Total Cats: 524
Default

Did you set the number of coils from "wasted" spark to "coil on plug" in Ignition Options?
99mx5 is offline  
Old 01-10-2011, 06:19 PM
  #11  
Ben
Supporting Vendor
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Default

Zuki,
I don't 100% understand your problem. Are you saying that TunerStudio is reporting that the DIYPNP is not firing injector 2? What do your pulsewidth gauges tell you, does pulsewidth1 = pulsewidth2 ?

How about taking a datalog of the DIYPNP running on the stim for 10 or 15 seconds, and posting it along with the .msq?

Justin,
Glad I was able to help you get that going
__________________
Chief of Floor Sweeping, DIYAutoTune.com & AMP EFI
Crew Chief, Car Owner & Least Valuable Driver, HongNorrthRacing

91 Turbo | 10AE Turbo | 01 Track Rat | #323 Mazda Champcar

Originally Posted by concealer404
Buy an MSPNP Pro, you'll feel better.
Ben is offline  
Old 01-11-2011, 05:07 PM
  #12  
Newb
 
zuki_dan's Avatar
 
Join Date: Mar 2010
Posts: 8
Total Cats: 0
Default

Originally Posted by 99mx5
Did you set the number of coils from "wasted" spark to "coil on plug" in Ignition Options?
Yes, I have changed the coils to coil on plug.
zuki_dan is offline  
Old 01-11-2011, 05:20 PM
  #13  
Newb
 
zuki_dan's Avatar
 
Join Date: Mar 2010
Posts: 8
Total Cats: 0
Default

Originally Posted by Ben
Zuki,
I don't 100% understand your problem. Are you saying that TunerStudio is reporting that the DIYPNP is not firing injector 2? What do your pulsewidth gauges tell you, does pulsewidth1 = pulsewidth2 ?

How about taking a datalog of the DIYPNP running on the stim for 10 or 15 seconds, and posting it along with the .msq?

Justin,
Glad I was able to help you get that going
Justin,
Under the tuning tab in tunerstudio in real time displays, all output channels the inj2 circuit just sits at 0. I have put all 4 pulsewidth gauges on my dash and they all match when using the stim.
Attached Files
File Type: msl
2011-01-11_17.14.48.msl (478.0 KB, 166 views)
File Type: msq
zuki_dan is offline  
Old 01-24-2011, 04:12 PM
  #14  
Newb
 
zuki_dan's Avatar
 
Join Date: Mar 2010
Posts: 8
Total Cats: 0
Default

It ended up being a defective mircosquirt module. Matt at DIYPNP took care of me.
zuki_dan is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
slomiata
MEGAsquirt
5
10-07-2015 01:11 PM
The Gleas
MEGAsquirt
3
10-01-2015 09:30 AM
lsc224
Miata parts for sale/trade
2
10-01-2015 09:17 AM


Thread Tools
Search this Thread
Quick Reply: INJ outputs not working on DIYPnP



All times are GMT -4. The time now is 08:49 PM.