FM/Begi down flow IC and piping - $150.00
#1
Junior Member
Thread Starter
iTrader: (3)
Join Date: Jul 2008
Location: Fresno CA
Posts: 137
Total Cats: 3
FM/Begi down flow IC and piping - $150.00
These parts have been sitting in my garage for about a year. The IC is in great condition. The pipes are in OK shape. The inlet pipe to the IC is a bit tweaked, but a torch and elbow grease will get it back into shape.
I'm asking $150.00 plus shipping.
SOLD
I'm asking $150.00 plus shipping.
SOLD
Last edited by twothirdsCobra; 12-02-2009 at 10:25 PM. Reason: This item is SOLD
#4
I'm Miserable!
iTrader: (16)
Join Date: Dec 2008
Location: where most people are Utarded
Posts: 1,296
Total Cats: 0
A/C and P/S compatible? Is all of the piping including Turbo outlet pipe and TB inlet pipe included?Pictures of the piping? How tweaked is the pipe and how did it happen, easy fix? How much power were you putting through it? Sorry for the questions, but I am seriously considering this for my 94 setup.
#5
Junior Member
Thread Starter
iTrader: (3)
Join Date: Jul 2008
Location: Fresno CA
Posts: 137
Total Cats: 3
Yes.
Yes. The silicone couplers are not included though. I may have a few extra ones in my storage that I'm not using and if so, I'll include them. They are black in color.
I can get the pics of the piping but it won't be before tomorrow evening.
It got tweaked by me. When PWR made my new Aero 2 IC unit, they mis-aligned the inlet to the IC by about 5 degrees. The coupler wouldn't stay on so I had to heat the pipe with a propane torch and bend it a bit to fit. I have since made all new piping which is why I am including this piping in the sale of the IC. The pipe should bend back using the same technique.
@ 12 lb., I make 238whp on CA 91, with race fuel I'm at 249 @ the same boost level. At this boost level, intake temps are usually within 15 degrees of ambient. Remember, it's a Begi unit, not a ebay knock off.
I can get the pics of the piping but it won't be before tomorrow evening.
It got tweaked by me. When PWR made my new Aero 2 IC unit, they mis-aligned the inlet to the IC by about 5 degrees. The coupler wouldn't stay on so I had to heat the pipe with a propane torch and bend it a bit to fit. I have since made all new piping which is why I am including this piping in the sale of the IC. The pipe should bend back using the same technique.
@ 12 lb., I make 238whp on CA 91, with race fuel I'm at 249 @ the same boost level. At this boost level, intake temps are usually within 15 degrees of ambient. Remember, it's a Begi unit, not a ebay knock off.
#9
Junior Member
Thread Starter
iTrader: (3)
Join Date: Jul 2008
Location: Fresno CA
Posts: 137
Total Cats: 3
Yes, there is some on the pipes, but a can of 3 dollar Krylon will fix that. No paint on the IC as you can see by the pic.
I have a better but much more expensive system now. I am running a custom PWR Aero 2 core IC with 2mm thick 2.25 OD aluminum tubes from the turbo outlet to the IC inlet, then custom formed silicone tubing from the IC outlet to the TB. This cost me around $700.00.
Nope, sorry just the funds. I already purchased all of the parts I need for this years "upgrades" and maintenance. Just trying to recoup some of the money by selling things I don't need/use any more.
I have a better but much more expensive system now. I am running a custom PWR Aero 2 core IC with 2mm thick 2.25 OD aluminum tubes from the turbo outlet to the IC inlet, then custom formed silicone tubing from the IC outlet to the TB. This cost me around $700.00.
Nope, sorry just the funds. I already purchased all of the parts I need for this years "upgrades" and maintenance. Just trying to recoup some of the money by selling things I don't need/use any more.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM