FS: RX7 TurboII transmission Conversion
#1
Miotta FTW!
Thread Starter
iTrader: (24)
Join Date: Jun 2006
Location: Chicagoland, IL
Posts: 4,290
Total Cats: 31
FS: RX7 TurboII transmission Conversion
FS: RX7 Turbo II transmission swap for Miata.
I bought this as an entire package, but only needed the rearend and axles.
For sale is:
1 RX7 turboII transmission (minus shifter), has slave cylinder and throughout arm
1 Custom aluminum adapter plate (made years ago by AMS, the big EVO shop)
1 Custom drive shaft for using with a mid 80s clutch lsd long nose RX7 rear, non-turbo II from what I know. ie: the 7" clutch one that basically bolts into car, and this retains the front longnose vs miata short.
Looking for 600obo for this. Will ship at buyer expense. I have a pallet outside garage right now... and can probably figure out freight some how.
You can ask all the install details you want, I honestly only know that the bell housing has some places modified, cut for stock starter. The adapter plate lines up with both engine and trans. Driveshaft matches on both sides and joints are tight.
So again... 600obo for this and more pictures coming after I get around to it.
I bought this as an entire package, but only needed the rearend and axles.
For sale is:
1 RX7 turboII transmission (minus shifter), has slave cylinder and throughout arm
1 Custom aluminum adapter plate (made years ago by AMS, the big EVO shop)
1 Custom drive shaft for using with a mid 80s clutch lsd long nose RX7 rear, non-turbo II from what I know. ie: the 7" clutch one that basically bolts into car, and this retains the front longnose vs miata short.
Looking for 600obo for this. Will ship at buyer expense. I have a pallet outside garage right now... and can probably figure out freight some how.
You can ask all the install details you want, I honestly only know that the bell housing has some places modified, cut for stock starter. The adapter plate lines up with both engine and trans. Driveshaft matches on both sides and joints are tight.
So again... 600obo for this and more pictures coming after I get around to it.
Last edited by Splitime; 07-31-2009 at 03:37 PM.
#4
Miotta FTW!
Thread Starter
iTrader: (24)
Join Date: Jun 2006
Location: Chicagoland, IL
Posts: 4,290
Total Cats: 31
Last I checked the TurboII trans doesn't come in any other gear flavors. It's a stock TII trans as far as I know.
Powerwise... I don't know beyond it beats out miata transmissions. Thus why many people have inquired about using one over the years.. but only people who made their own custom adapter plates actually did it.
Powerwise... I don't know beyond it beats out miata transmissions. Thus why many people have inquired about using one over the years.. but only people who made their own custom adapter plates actually did it.
#11
Elite Member
iTrader: (24)
Join Date: Jun 2007
Location: Woodland Hills, CA
Posts: 4,667
Total Cats: 18
i want it but i dont want to deal with custom driveshaft to use it with my badass rear end. i think its just going to be easier for me to drop 6 speed tranny once my current 5 speed gives up (it will do it soon)
#13
Elite Member
iTrader: (24)
Join Date: Jun 2007
Location: Woodland Hills, CA
Posts: 4,667
Total Cats: 18
true... but i dont think i can manage to break 6 speed with under 200whp... remember, no turbo? anyways... how much is shipping to 90046? any chance you could just sell adapter plate so i dont have to pay $$$$ for shipping the whole thing? i know its a long shot to ask for something like that but...
#15
Senior Member
iTrader: (2)
Join Date: May 2005
Location: Edmonton Ab, Canada
Posts: 1,202
Total Cats: 21
Split- I need a shipping quote to T8R 0A3 Morinville Ab Canada. I just blew the **** out of my tranny last night, urban **** off you don't need this ****.
Would you be willing to just sell the adapter plate for a few bux less?
Do you retain the miata clutch when using this thing?
Thanks,
-Dean
Would you be willing to just sell the adapter plate for a few bux less?
Do you retain the miata clutch when using this thing?
Thanks,
-Dean
#16
Senior Member
iTrader: (1)
Join Date: Jun 2006
Location: Outside of the Loop-ATL
Posts: 761
Total Cats: 1
Split- I need a shipping quote to T8R 0A3 Morinville Ab Canada. I just blew the **** out of my tranny last night, urban **** off you don't need this ****.
Would you be willing to just sell the adapter plate for a few bux less?
Do you retain the miata clutch when using this thing?
Thanks,
-Dean
Would you be willing to just sell the adapter plate for a few bux less?
Do you retain the miata clutch when using this thing?
Thanks,
-Dean
This is assuming that, that is a stock unmodified R tranny.