T2 1.6 Turbo kit 304L, everything you need to turbo
10-23-2015, 03:23 PM
#21
Junior Member
Join Date: Apr 2015
Location: salt lake city UTAH
Posts: 88
Total Cats: -1
Actually what I really need is those injectors how much ?
0
10-23-2015, 03:32 PM
#22
Junior Member
Join Date: Oct 2009
Location: Stamford, CT
Posts: 212
Total Cats: 3
Is this being parted? Are you taking offers on any pieces at this point?
0
10-24-2015, 12:13 PM
#23
I am still trying to keep it together as a whole kit at this point. Everything works so well together that it would be a shame for me to split it up for someone looking for a whole kit...
With that said, I am taking offers on pieces and keeping a tab of them for who wants what, and if I can part out the whole kit that way, then I will probably do it.
With that said, I am taking offers on pieces and keeping a tab of them for who wants what, and if I can part out the whole kit that way, then I will probably do it.
0
10-24-2015, 05:24 PM
#24
Junior Member
Join Date: Oct 2009
Location: Stamford, CT
Posts: 212
Total Cats: 3
I'd be in for $800 for manifold, turbo, water/oil lines, and downpipe.
0
10-25-2015, 12:25 AM
#25
Junior Member
Join Date: Apr 2015
Location: salt lake city UTAH
Posts: 88
Total Cats: -1
I'll give you 85 for the injectors
0
10-25-2015, 12:27 AM
#26
Junior Member
Join Date: Apr 2015
Location: salt lake city UTAH
Posts: 88
Total Cats: -1
85 for injectors?
0
10-25-2015, 10:00 PM
#27
Newb
Join Date: Oct 2015
Location: Columbus, Ohio
Posts: 20
Total Cats: 4
Hoping this sells as a kit, but if it doesn't, i'd grab that AEM with sensor...
0
10-26-2015, 12:17 AM
#28
Parting out has begun. What's left is what's below:
RX-8 440cc injectors ($100 shipped)
MS3x PNP for 1990 1.6 built by Braineack... Full sequential injection/ignition, LS1 coil packs, GM electronic boost controller, Fuel injector wiring for easy connection into OEM wiring, LS1 coil packs + wiring, MSD 8.5mm spark plug wires, GM IAT sensor, jumper wire, Aluminum/Nylon 3D printed VTPS bracket with VISHNAY VTPS fits easy.
The wiring should be streamlined and everything is labeled exactly where it needs to go. I even left some of the OEM wires attached for easy match up. Also includes wiring diagrams I made. ($1500 shipped)
Intercooler + 2.5" piping with silicone reducer for T25 turbo, IAT bung welded in along with IACV bung ($260 shipped)
3" exhaust setup - minus down pipe ($300, maybe would ship... depending where.)
AEM wideband, less than 500 miles, + dual gauge a-pillar, + glowshift boost gauge. ($220 shipped)
RX-8 440cc injectors ($100 shipped)
MS3x PNP for 1990 1.6 built by Braineack... Full sequential injection/ignition, LS1 coil packs, GM electronic boost controller, Fuel injector wiring for easy connection into OEM wiring, LS1 coil packs + wiring, MSD 8.5mm spark plug wires, GM IAT sensor, jumper wire, Aluminum/Nylon 3D printed VTPS bracket with VISHNAY VTPS fits easy.
The wiring should be streamlined and everything is labeled exactly where it needs to go. I even left some of the OEM wires attached for easy match up. Also includes wiring diagrams I made. ($1500 shipped)
Intercooler + 2.5" piping with silicone reducer for T25 turbo, IAT bung welded in along with IACV bung ($260 shipped)
3" exhaust setup - minus down pipe ($300, maybe would ship... depending where.)
AEM wideband, less than 500 miles, + dual gauge a-pillar, + glowshift boost gauge. ($220 shipped)
0
10-26-2015, 10:03 PM
#31
Newb
Join Date: Oct 2015
Location: Columbus, Ohio
Posts: 20
Total Cats: 4
0
Thread
Thread Starter
Forum
Replies
Last Post
