Begi-S kit is in! After thoughts and questions
#21
Junior Member
Thread Starter
iTrader: (3)
Join Date: Mar 2008
Location: Sunnyvale, ca
Posts: 220
Total Cats: 0
the code that was pulled was P507 which is high idle. I read that it was possible to tighten the idle air screw on the throttle body so i attempted this... i got the idle down to 1100. Still not sure what to do to get it to the correct idle rpm!
Any Ideas??!!
Any Ideas??!!
#22
Junior Member
Thread Starter
iTrader: (3)
Join Date: Mar 2008
Location: Sunnyvale, ca
Posts: 220
Total Cats: 0
the idle whent down to 1100 as i tightedn the screw and it stayed their. I had to drive the car again, and its back to 1500-1700ish. When I am in gear and push the clutch in, the rpms drop slightly like they are supposed to below 1500, and then they go up to the rpm they stick at.
no idea where to go from here..
no idea where to go from here..
#24
Junior Member
Thread Starter
iTrader: (3)
Join Date: Mar 2008
Location: Sunnyvale, ca
Posts: 220
Total Cats: 0
Please help!!
Thanks,
Henry
#26
Junior Member
Thread Starter
iTrader: (3)
Join Date: Mar 2008
Location: Sunnyvale, ca
Posts: 220
Total Cats: 0
No the idle is high but pretty stable.. I though I would get a cel code if that went out... Is there a way to check to see if its the tps? The car drives normally besides the idle...
#27
Junior Member
Thread Starter
iTrader: (3)
Join Date: Mar 2008
Location: Sunnyvale, ca
Posts: 220
Total Cats: 0
I bypassed the turbo to the intake and idle was still high.
i pulled back the tb, and cleaned it with carb cleaner..
the idle was pretty much good for a few minutes! then whent high again... back to 1500.
I turned the car off, a few mins later started the car, again the idle was good for a minute or so, then whent back to its high point after driving for a bit.
what can this be??? really need the help guys!
thanks,
Henry
i pulled back the tb, and cleaned it with carb cleaner..
the idle was pretty much good for a few minutes! then whent high again... back to 1500.
I turned the car off, a few mins later started the car, again the idle was good for a minute or so, then whent back to its high point after driving for a bit.
what can this be??? really need the help guys!
thanks,
Henry
#31
Junior Member
Thread Starter
iTrader: (3)
Join Date: Mar 2008
Location: Sunnyvale, ca
Posts: 220
Total Cats: 0
When I do this, nothing changes! The idle remains high! Is my IAC bad? I thought when an IAC goes bad, the car surges, not has a high idle! not even sure whats supposed to happen though when the thing is disconnected.. can someone go and try it on their car for me??
I took off the tb again though and tried to take the iac off, I got one screw out and stripped the other screw. I found a screw that i will use to replace the stripped one, but my stripped screw puller tool was too smal . i sprayed carb cleaner in the tb opening that goes to the iac, and the car idled fine (about 900 rpm) for about 10 mins.. when i started to drive the car, the idle whent high again, and its going from 1600 to 1900 now, just back and forth. this makes it more difficult to drive.. and just even more of a pain in the ***!!!
Help!
what do i do?
I took off the tb again though and tried to take the iac off, I got one screw out and stripped the other screw. I found a screw that i will use to replace the stripped one, but my stripped screw puller tool was too smal . i sprayed carb cleaner in the tb opening that goes to the iac, and the car idled fine (about 900 rpm) for about 10 mins.. when i started to drive the car, the idle whent high again, and its going from 1600 to 1900 now, just back and forth. this makes it more difficult to drive.. and just even more of a pain in the ***!!!
Help!
what do i do?
#33
A possible hint regarding the 1500RPM surge.
Immediately on startup, 99s usually do jump to a higher than normal RPM, then settle down, eventually to the normal idle. The high RPM (1500) is not that far from norm.
Many turbos produce some additional airflow at idle, once they start spinning. The FM SBB on my 99 will cause the air flow metering to indicate 2x the normal air flow at idle if there is an air leak between the turbo and the intake manifold. This will cause a "pig rich" condition, and cause the engine to blubber out with a closed throttle plate.
Initially the system is in open loop, so the air bleed screw may need to be adjusted slightly. Too much and you may cause the dreaded "idle droup", or an ECU light. The light will usually code out to --The Idle speed is not controllable to within the programmed idle limits. I assume you are using the stock ECU. AMkt ECUs behave very differently, depending on what unit is used. My 99 has the older Link "Piggy", stock injectors, and four additional injectors mounted on the intake manifold.
The air temp sensor will tend to cause a slightly rich setting by the ECU if other inputs allow. Conversely, if the sensor was mounted in say the airflow between an intercooler and the intake manifold, it would result in a higher reading, and might cause the ECU to set for a slightly leaner condition.
(Assuming that you had a way to keep the sensor from popping out under boost.)
The "stock" location of the temp sensor produced a reading that was more or less the same as the temperature at the intake of the air flow sensor.
Mine is mounted in a rubber grommet that gives a bit of isolation from the intake piping between the air flow sensor and the turbo.
Immediately on startup, 99s usually do jump to a higher than normal RPM, then settle down, eventually to the normal idle. The high RPM (1500) is not that far from norm.
Many turbos produce some additional airflow at idle, once they start spinning. The FM SBB on my 99 will cause the air flow metering to indicate 2x the normal air flow at idle if there is an air leak between the turbo and the intake manifold. This will cause a "pig rich" condition, and cause the engine to blubber out with a closed throttle plate.
Initially the system is in open loop, so the air bleed screw may need to be adjusted slightly. Too much and you may cause the dreaded "idle droup", or an ECU light. The light will usually code out to --The Idle speed is not controllable to within the programmed idle limits. I assume you are using the stock ECU. AMkt ECUs behave very differently, depending on what unit is used. My 99 has the older Link "Piggy", stock injectors, and four additional injectors mounted on the intake manifold.
The air temp sensor will tend to cause a slightly rich setting by the ECU if other inputs allow. Conversely, if the sensor was mounted in say the airflow between an intercooler and the intake manifold, it would result in a higher reading, and might cause the ECU to set for a slightly leaner condition.
(Assuming that you had a way to keep the sensor from popping out under boost.)
The "stock" location of the temp sensor produced a reading that was more or less the same as the temperature at the intake of the air flow sensor.
Mine is mounted in a rubber grommet that gives a bit of isolation from the intake piping between the air flow sensor and the turbo.
Finally got the Begi-s kit in on my 99. Overall, the install was not too bad at all and took, pretty much 2 days going at a leisurly pace.(12ish hours of work)
Tapping the pan was easy, The EGR was a pain but it was just time consuming.
I am currently not running any boost since my EMB harness is coming tomorrow. I am also planning on putting on the intercooler and bov tomoroww as well.
I currently have an exhaust leak coming from either the downpipe to catback flange, or the between the two downpipe pieces. (they where kind of hard to tighten.) if its between the dp and catback. i will just use some copper rtv sealant stuff, but otherwise i can try to see how much tighter i can get the two downpipe pieces. Does anyone have any experience with this? tips?
Also, the piece that goes from the maf to turbo doesnt have an ait sensor bung or anything... i currently have the ait(stock) sitting next to the air intake.. i guess this should be ok... but wondering if this is ok and how its supposed to be.
otherwise the car seems to be fine, except for my idle being higher than before, (1500 rpm) for maybe 30-60 seconds. when the car is warmed up, it idles normally.. just wondering what this could be caused from and , if its normal. (my friends mark III supra does this as well)
i am currently being very carefull and not going into boost even with the actuator disconnected. I am hoping to get the management and intercooler in, in the next few days! cant wait!
Tapping the pan was easy, The EGR was a pain but it was just time consuming.
I am currently not running any boost since my EMB harness is coming tomorrow. I am also planning on putting on the intercooler and bov tomoroww as well.
I currently have an exhaust leak coming from either the downpipe to catback flange, or the between the two downpipe pieces. (they where kind of hard to tighten.) if its between the dp and catback. i will just use some copper rtv sealant stuff, but otherwise i can try to see how much tighter i can get the two downpipe pieces. Does anyone have any experience with this? tips?
Also, the piece that goes from the maf to turbo doesnt have an ait sensor bung or anything... i currently have the ait(stock) sitting next to the air intake.. i guess this should be ok... but wondering if this is ok and how its supposed to be.
otherwise the car seems to be fine, except for my idle being higher than before, (1500 rpm) for maybe 30-60 seconds. when the car is warmed up, it idles normally.. just wondering what this could be caused from and , if its normal. (my friends mark III supra does this as well)
i am currently being very carefull and not going into boost even with the actuator disconnected. I am hoping to get the management and intercooler in, in the next few days! cant wait!
#34
Junior Member
Thread Starter
iTrader: (3)
Join Date: Mar 2008
Location: Sunnyvale, ca
Posts: 220
Total Cats: 0
Looks like I figured out what was going on. Took apart the iac and hooked up the connector to the car and turned the car on, it made a high pitched noise. figured that wasnt normal... made a temporary duct tape gasket closing of the iac port.
adjusted idle and now idles like a champ. have to give it a bit of gas during really really cold starts for 5-10 seconds... (iac valve allows more air in for higher idle during cold start)
when i did extensive searches for this issue, i saw a few similar cases, but they didnt have solutions..
hopefully someone finds this thread usefull in the future and they dont have to go crazy trying to figure out whats going on!
adjusted idle and now idles like a champ. have to give it a bit of gas during really really cold starts for 5-10 seconds... (iac valve allows more air in for higher idle during cold start)
when i did extensive searches for this issue, i saw a few similar cases, but they didnt have solutions..
hopefully someone finds this thread usefull in the future and they dont have to go crazy trying to figure out whats going on!
#35
while you have the down pipe assessable I would remove it wield it to one piece and cut off that long retaining bolt loops. I had lots of problems with that hitting the underframe.
The AIT can be installed just past the MAF as long as you make sure that you dont allow any leaks, or else mount it externally next to the Air filter, it just needs to read temperatures going into the MAF.
The AIT can be installed just past the MAF as long as you make sure that you dont allow any leaks, or else mount it externally next to the Air filter, it just needs to read temperatures going into the MAF.
#36
Junior Member
Thread Starter
iTrader: (3)
Join Date: Mar 2008
Location: Sunnyvale, ca
Posts: 220
Total Cats: 0
I don't think I am having problems with the dp any more. Took a bunch of time but I tightened down that long bolt pretty good.. Its in a very difficult area to reach while the down pipe is on the car. If the bolt guides where rotated about 180 degrees it would be MUCH easier to tighten due to clearance issues. If they where also maybe a few more mm away from the pipe, it would have been possible to fit a socket over the bolt, which also would have made it much much easier.
Anyway, today hopefully I can get the intercooler, bov and emb on so I can tune and boost finally!!
Anyway, today hopefully I can get the intercooler, bov and emb on so I can tune and boost finally!!
Thread
Thread Starter
Forum
Replies
Last Post
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM