TurboTony DP installed today!
#1
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
TurboTony DP installed today!
Here's my story to go along with the title. The total install took about 4 hours damn IL and rust. The quality of the product was awesome, I had the 2 piece with flex and o2 bung by the cat. First off I don't know if I can feel a difference in spool or power, feels the same as with the 3" exhaust. But now 2 problems I have are, I couldn't get a nut or bolt on the bottom of the flange right where it connects to the turbo, any problems with that? seems like it doesn't leak. And now my wideband reads alot different than with the stock dp, in vacuum it reads way lean, but boost way rich. So can it be an exhaust leak, or it needs recalibrated? Would it mess up my tune just by swapping DP's I don't know if I believe the wideband?
#2
My TT dp was a pain to install too. Agreed on the awesome quality.
Surely there is a difference between that and the craptastic greddy DP.
For the bottom bolt, I took a grinder to the head of it and removed allot of material along with shortening the entire bolt too. I'd put that in if I were you.
I'd start by recalibrating your wideband, easiest thing to do. If that doesn't fix it then look or listen for exhaust leaks.
You should be a tad leaner in boost now due to the better overall VE of your engine. Probably not dangerous but you will be leaner. I went from stock catback exhaust to just an open cat and started seeing 12.6 in boost.
Surely there is a difference between that and the craptastic greddy DP.
For the bottom bolt, I took a grinder to the head of it and removed allot of material along with shortening the entire bolt too. I'd put that in if I were you.
I'd start by recalibrating your wideband, easiest thing to do. If that doesn't fix it then look or listen for exhaust leaks.
You should be a tad leaner in boost now due to the better overall VE of your engine. Probably not dangerous but you will be leaner. I went from stock catback exhaust to just an open cat and started seeing 12.6 in boost.
#3
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
My TT dp was a pain to install too. Agreed on the awesome quality.
Surely there is a difference between that and the craptastic greddy DP.
For the bottom bolt, I took a grinder to the head of it and removed allot of material along with shortening the entire bolt too. I'd put that in if I were you.
I'd start by recalibrating your wideband, easiest thing to do. If that doesn't fix it then look or listen for exhaust leaks.
You should be a tad leaner in boost now due to the better overall VE of your engine. Probably not dangerous but you will be leaner. I went from stock catback exhaust to just an open cat and started seeing 12.6 in boost.
Surely there is a difference between that and the craptastic greddy DP.
For the bottom bolt, I took a grinder to the head of it and removed allot of material along with shortening the entire bolt too. I'd put that in if I were you.
I'd start by recalibrating your wideband, easiest thing to do. If that doesn't fix it then look or listen for exhaust leaks.
You should be a tad leaner in boost now due to the better overall VE of your engine. Probably not dangerous but you will be leaner. I went from stock catback exhaust to just an open cat and started seeing 12.6 in boost.
I agree I need the bolt in there but I cut the bolt and it just wont thread in there and in boost the wideband reads in the 9's but at idle is the same as before the DP so I dont know what to do? And I tried recalibrating it today but couldn't tell if it recalibrated or not?
#4
Use a sanding wheel thingy (technical term) to chamfer the threaded end of the bolt, that should let it thread in.
Unplug the sensor, turn key to ON position for 20 seconds then turn it OFF. Plug the sensor back in with it hanging in the air. Then turn the key ON. This will do a full reset of the sensor, it worked when my sensor was acting up.
Unplug the sensor, turn key to ON position for 20 seconds then turn it OFF. Plug the sensor back in with it hanging in the air. Then turn the key ON. This will do a full reset of the sensor, it worked when my sensor was acting up.
#5
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
Use a sanding wheel thingy (technical term) to chamfer the threaded end of the bolt, that should let it thread in.
Unplug the sensor, turn key to ON position for 20 seconds then turn it OFF. Plug the sensor back in with it hanging in the air. Then turn the key ON. This will do a full reset of the sensor, it worked when my sensor was acting up.
Unplug the sensor, turn key to ON position for 20 seconds then turn it OFF. Plug the sensor back in with it hanging in the air. Then turn the key ON. This will do a full reset of the sensor, it worked when my sensor was acting up.
yea I didnt do all that so your saying unplug the sensor from the box turn key on for 30 secs then back off, plug back in and turn key on with sensor hanging in the air then back off then unplug and screw back into exhaust then its good to go?
#10
Unplug and remove the sensor then do this:
"3 First Time Use
1. Do not connect the sensor yet.
2. Switch 12V supply to the LC-1 on and wait for 10 seconds.
3. Switch the 12V supply off after 10 seconds.
4. Connect the sensor to the sensor interface connector. The sensor must be exposed to air
for the first time calibration.
- 9 -
5. Switch the LC-1 on and wait for 2 minutes.
If you connected a LED to the calibration button, you will at first see the LED blink slowly and
steadily. If it blinks for a fixed number of pulses, then switches off for 2 seconds and then repeats,
you have an error code. See Appendix for details.
Slow and steady blinking indicates that the sensor is warming up to its optimum operating
temperature. The warm-up period will last for about 30 seconds for a cold sensor, depending on
the sensor type used.
After the sensor is warmed up the meter automatically calibrates the sensor heater controller to
the particular sensor. During this 20-second period the LC-1 collects and calculates sensor
specific data required to quickly reach operating temperature in the future. After the first time use
the meter will use these values to regulate the sensor's temperature. During the heater calibration
the optional LED will blink fast and steady.
After the heater calibration is finished you should perform a free air calibration. The free air
calibration is accomplished by either pressing the push-button or connecting the black wire to
ground for three seconds and then releasing. During this procedure a connected LED will go off.
The LC-1 will now calibrate itself by using air as a reference gas with known oxygen content.
After the free air calibration is finished the LED should light up steady and continuously,
indicating correct operation of the LC-1."
Taken from the manual.
"3 First Time Use
1. Do not connect the sensor yet.
2. Switch 12V supply to the LC-1 on and wait for 10 seconds.
3. Switch the 12V supply off after 10 seconds.
4. Connect the sensor to the sensor interface connector. The sensor must be exposed to air
for the first time calibration.
- 9 -
5. Switch the LC-1 on and wait for 2 minutes.
If you connected a LED to the calibration button, you will at first see the LED blink slowly and
steadily. If it blinks for a fixed number of pulses, then switches off for 2 seconds and then repeats,
you have an error code. See Appendix for details.
Slow and steady blinking indicates that the sensor is warming up to its optimum operating
temperature. The warm-up period will last for about 30 seconds for a cold sensor, depending on
the sensor type used.
After the sensor is warmed up the meter automatically calibrates the sensor heater controller to
the particular sensor. During this 20-second period the LC-1 collects and calculates sensor
specific data required to quickly reach operating temperature in the future. After the first time use
the meter will use these values to regulate the sensor's temperature. During the heater calibration
the optional LED will blink fast and steady.
After the heater calibration is finished you should perform a free air calibration. The free air
calibration is accomplished by either pressing the push-button or connecting the black wire to
ground for three seconds and then releasing. During this procedure a connected LED will go off.
The LC-1 will now calibrate itself by using air as a reference gas with known oxygen content.
After the free air calibration is finished the LED should light up steady and continuously,
indicating correct operation of the LC-1."
Taken from the manual.
#11
Senior Member
Thread Starter
iTrader: (8)
Join Date: Aug 2006
Location: Springfield, IL
Posts: 1,012
Total Cats: 0
Unplug and remove the sensor then do this:
"3 First Time Use
1. Do not connect the sensor yet.
2. Switch 12V supply to the LC-1 on and wait for 10 seconds.
3. Switch the 12V supply off after 10 seconds.
4. Connect the sensor to the sensor interface connector. The sensor must be exposed to air
for the first time calibration.
- 9 -
5. Switch the LC-1 on and wait for 2 minutes.
If you connected a LED to the calibration button, you will at first see the LED blink slowly and
steadily. If it blinks for a fixed number of pulses, then switches off for 2 seconds and then repeats,
you have an error code. See Appendix for details.
Slow and steady blinking indicates that the sensor is warming up to its optimum operating
temperature. The warm-up period will last for about 30 seconds for a cold sensor, depending on
the sensor type used.
After the sensor is warmed up the meter automatically calibrates the sensor heater controller to
the particular sensor. During this 20-second period the LC-1 collects and calculates sensor
specific data required to quickly reach operating temperature in the future. After the first time use
the meter will use these values to regulate the sensor's temperature. During the heater calibration
the optional LED will blink fast and steady.
After the heater calibration is finished you should perform a free air calibration. The free air
calibration is accomplished by either pressing the push-button or connecting the black wire to
ground for three seconds and then releasing. During this procedure a connected LED will go off.
The LC-1 will now calibrate itself by using air as a reference gas with known oxygen content.
After the free air calibration is finished the LED should light up steady and continuously,
indicating correct operation of the LC-1."
Taken from the manual.
"3 First Time Use
1. Do not connect the sensor yet.
2. Switch 12V supply to the LC-1 on and wait for 10 seconds.
3. Switch the 12V supply off after 10 seconds.
4. Connect the sensor to the sensor interface connector. The sensor must be exposed to air
for the first time calibration.
- 9 -
5. Switch the LC-1 on and wait for 2 minutes.
If you connected a LED to the calibration button, you will at first see the LED blink slowly and
steadily. If it blinks for a fixed number of pulses, then switches off for 2 seconds and then repeats,
you have an error code. See Appendix for details.
Slow and steady blinking indicates that the sensor is warming up to its optimum operating
temperature. The warm-up period will last for about 30 seconds for a cold sensor, depending on
the sensor type used.
After the sensor is warmed up the meter automatically calibrates the sensor heater controller to
the particular sensor. During this 20-second period the LC-1 collects and calculates sensor
specific data required to quickly reach operating temperature in the future. After the first time use
the meter will use these values to regulate the sensor's temperature. During the heater calibration
the optional LED will blink fast and steady.
After the heater calibration is finished you should perform a free air calibration. The free air
calibration is accomplished by either pressing the push-button or connecting the black wire to
ground for three seconds and then releasing. During this procedure a connected LED will go off.
The LC-1 will now calibrate itself by using air as a reference gas with known oxygen content.
After the free air calibration is finished the LED should light up steady and continuously,
indicating correct operation of the LC-1."
Taken from the manual.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM