How to get oil pan off?
#1
I'm Miserable!
Thread Starter
iTrader: (-1)
Join Date: May 2007
Location: West Sacramento Ca
Posts: 944
Total Cats: 0
How to get oil pan off?
Is it possible to have the car on the lift and remove everything that is visible and in the way of the oil pan to get the pan off? without pulling the motor
#4
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
The guy tapping your pan is an idiot. Use the FM instructions.
-23/32" hole
-1/2" NPT tap
Don't drill more than 1/4" or so into the pan, just barely enough to make a hole. The pickup is right behind where you have to drill. Go slow, and grease the hell out of the bit (dip the bit in thick grease). Tap the same way; again, don't go too deep. Clean everything up, thread your fitting in, throw some JBWeld on it, and hook up your return line. Pour a quart of paint thinner into the return line with the drain plug out to get the chips you missed with the grease.
Seriously, hundreds if not thousands of people have done it that way with no issues reported. Dropping your oil pan requires pulling the motor or dropping the front subframe, and it's completely unnecessary.
-23/32" hole
-1/2" NPT tap
Don't drill more than 1/4" or so into the pan, just barely enough to make a hole. The pickup is right behind where you have to drill. Go slow, and grease the hell out of the bit (dip the bit in thick grease). Tap the same way; again, don't go too deep. Clean everything up, thread your fitting in, throw some JBWeld on it, and hook up your return line. Pour a quart of paint thinner into the return line with the drain plug out to get the chips you missed with the grease.
Seriously, hundreds if not thousands of people have done it that way with no issues reported. Dropping your oil pan requires pulling the motor or dropping the front subframe, and it's completely unnecessary.
#5
+1, I would say at least hundreds of us have done it wothout removing the pan.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#7
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,501
Total Cats: 4,080
It's been done this was for over 10 years.
There's nothing on to installing a turbo kit that would require pulling an engine or dropping the pan.
I'd suggest you and your friend invest in some *****, read up, and do the tried and true way. The only one I've hear dof screwing it up is Loki, but that's because he's a silly curled hair freak.
#11
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,046
Total Cats: 6,607
9.6 volt Makita right-angle FTW.
Although 1/2" NPT is the prevelant size, you can also use a 3/8" NPT. Slightly easier to drill and tap, and more compact. The ID of a 3/8" fitting is roughly the same as a -10AN fitting, which is what I am using for the rest of the drain line. It's perfectly adequate and will be slightly easier to do.
I can understand your mechanic's hesitation to go blindly drilling into the oil pan, especially since the oil pickup tube is right behind where you'll be drilling, but it is a relatively safe procedure that's been done hundreds of times.
Although 1/2" NPT is the prevelant size, you can also use a 3/8" NPT. Slightly easier to drill and tap, and more compact. The ID of a 3/8" fitting is roughly the same as a -10AN fitting, which is what I am using for the rest of the drain line. It's perfectly adequate and will be slightly easier to do.
I can understand your mechanic's hesitation to go blindly drilling into the oil pan, especially since the oil pickup tube is right behind where you'll be drilling, but it is a relatively safe procedure that's been done hundreds of times.
#15
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,046
Total Cats: 6,607
The trick for me was to disconnect the P/S lines and the steering column, remove the four bolts that hold the rack to the frame, and let the steering rack hang down supported by the tie rods. Opened up plenty o' space.
Thread
Thread Starter
Forum
Replies
Last Post
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM