Originally Posted by aidandj
(Post 1214230)
|
Originally Posted by aidandj
(Post 1214227)
|
So i wired this thing all up, and racechrono and another external GPS app don't show anyhting. Racechrono starts at "Connecting to GPS", then bounces between "No Data from GPS", and "No fix to satellites".
The red LED on the GPS is flashing, when as I understand it means it has a fix. Any suggestions? |
Originally Posted by Schuyler
(Post 1221035)
So i wired this thing all up, and racechrono and another external GPS app don't show anyhting. Racechrono starts at "Connecting to GPS", then bounces between "No Data from GPS", and "No fix to satellites".
The red LED on the GPS is flashing, when as I understand it means it has a fix. Any suggestions? Also connect it to your computer and see what the output is. I had some issues with the one without a flash chip. Enough screwing with setting got it working though. |
2 Attachment(s)
See, I drank beers and did this at 3am, and was quite confident it would work first try. So, it is a little compact to debug. Connecting to the computer via the gps only would likely prove somewhat difficult, as I planned on doing all the settings via Serial, without two-way communication. i.e. Serial only sends, as receive is going to Bluetooth. (also, don't hate on the soldering. harbor freight iron with a horrible tip :( My roommate moved to FL with his weller. I need to invest.)
Components: Arduino Nano v3 (Arduino) HC-06 Bluetooth module (Bluetooth) REYAX RYN25GI u-blox MAX-7C GPS/QZSS (GPS) (The one without flash memory) Arduino 5V -> GPS VDD Arduino 3v3 -> Bluetooth VCC Arduino 3v3 -> Bluetooth Wakeup Arduino TX1 -> GPS RX GPS TX -> Bluetooth RX GPS Gnd -> Bluetooth Gnd -> Arduino GND (I think that's everything) Attachment 234394 Attachment 234395 |
What's Bluetooth wakeup?
|
1 Attachment(s)
My guesses were strictly based on what it sounds like, but i had no lights on the bluetooth module, nor could I find it with my phone, until I brought that pin HIGH.
https://www.miataturbo.net/attachmen...ine=1428097342 |
In the past with the hc-05s I've used that pin sets it to master. But yours might be different can you connect to a terminal and see what's up? U-center should work.
|
Originally Posted by aidandj
(Post 1221205)
What's Bluetooth wakeup?
|
can't get mine on 10Hz :(
pinout as above arduino sent to gps "$PMTK220,100*2F" "$PMTK314,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0*29 " |
Originally Posted by aidandj
(Post 1221211)
In the past with the hc-05s I've used that pin sets it to master. But yours might be different can you connect to a terminal and see what's up? U-center should work.
|
You should be able to connector to u-center over Bluetooth.
|
1 Attachment(s)
Removed the wakeup pin. Assuming all I had to do was select the right Com Port, this is all I get:
Attachment 234393 |
What about just a serial terminal.
|
aidandj
are your GPS modules already at 10Hz or you have to put them there yourself on if so, how do you do that? you also change the baud rate? |
|
No they default to 1Hz. I use u-center to change the settings. Eventually I will try and see what commands u-center uses but right now I'm too busy actually making them.
Nope I leave baud at 9600. |
thanks
batery will make the unit remeber the 10Hz setting? |
Originally Posted by creon
(Post 1221949)
thanks
batery will make the unit remeber the 10Hz setting? |
I read somewhere that the chip itself sees that he can not send as much data on 9600
and that he then switched back to 1Hz Tonight another attempt otherwise I have to figure out how I can put every time you start the setting to 10Hz using the Arduino |
All times are GMT -4. The time now is 11:59 PM. |
© 2024 MH Sub I, LLC dba Internet Brands