Coilover spring length
#21
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
I acutally have 336 lb rear springs at 6" and they are binding. what shocks are you on?
I've always had binding issues on springs others can get away with, my car is heavy...calculations put it at 567lbs on the rear corners.
My springs are only 3.75" long at rest, per Tein's specs they have a max stroke of 3.7", so I only have 1.45" of travel before bind...I'm pretty sure my bump is getting compressed, but the spring is binding just before the bump will stop the shock travel.
here's mine at rest, ride height of 12.75" but I had to preload them a bit to bring it up to that:
#22
I have revalved R-Package Bilsteins which have a shorter body that the standard Bilsteins. I have been keeping an eye on the springs (Eibachs on Ground controls BTW)to watch out for this, but I see no evidence of bind like marks on the springs and I have never felt the (so I'm told) sharp bottoming out either.
One of these days I need to actually measure to see if it is possible with a big enough bump, but so far, no problems. I don't have my corner weights on hand at the moment, but I do recall them being less than yours.
One of these days I need to actually measure to see if it is possible with a big enough bump, but so far, no problems. I don't have my corner weights on hand at the moment, but I do recall them being less than yours.
#23
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
I did the math, since the 6" 336lb spring is compressed 2.5", that puts the weight to 756. Multiplied by the motion ratio of 0.75 in the rear, brings the weight on that corner around ~565 lbs.
But like I said, never head of anyone else with Teins complaning about it.
Luckily I found some 6.7" 336lb springs for $45 shipped for the pair. Gives me .7" more travel in the rear before bind (assuming all things equal). I think the ones I purchased have less coils so therefore more max stroke before bind.
But like I said, never head of anyone else with Teins complaning about it.
Luckily I found some 6.7" 336lb springs for $45 shipped for the pair. Gives me .7" more travel in the rear before bind (assuming all things equal). I think the ones I purchased have less coils so therefore more max stroke before bind.
#24
It looks like you have the marks in the powder coating a bit, yes? I had my car corner-weighed last spring and have the numbers. I'll look them up when I get home.
I do plan go to a 7-8" spring at some point to be safe but for now, it seems to work pretty well. The car is not DD though so I don;t put it through all the normal assault and battery most suspensions get on our MN roads.
I do plan go to a 7-8" spring at some point to be safe but for now, it seems to work pretty well. The car is not DD though so I don;t put it through all the normal assault and battery most suspensions get on our MN roads.
#27
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
Judge for yourself how much adjustment room youll have. Assuming the picture above shows the springs compressed down to 4.5" under weight and that puts me at a 12.75-13.0" ride height. If they were the same length but 100lbs heavier, theyd be at 5.11" compressed under body weight. I'd have to lower the spring perch about half an inch lower just to see the same ride height. I really wouldn't have anymore room to adjust the car lower. Unless you get the real koni sleeves which allow the collars to go down past the circlips, unlike the collars I have, you'd be screwed.
#28
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
Brain, this might be a better option:
http://www.sg-motorsport.com/store/p...oducts_id=1142
http://www.sg-motorsport.com/store/p...oducts_id=1142
why would that be better? sure they will allow me to reduce the preload, but they are also 3x the price of my solution and are too narrow ID.
#30
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
Look at my post again. I'm running koni shocks with NB tophats.
Those are 7" 300# springs and the car was at 12.75-13.0" ride height. Thre is barely enough room to go lower with my collars.
You'll be cutting it close is all I'm saying. YMMV
#32
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
I guess it really depends on the sleeves you use. If you get genuine Koni sleeves with the single locking collar, I think you'd be fine with 400# 7" springs. In my case I don't think they'd fit due to my cheapo ebay sleeves that have to rest on the spring perch.
and if your car is lighter than mine...
#33
So 5"f and 6"r would be the better option then like stated above. What can the regular Komi sports hold for spring rates front and rear. I was thinking maybe a better option would be to use Komi sports all around with rates of 500-550f and 400r with nb top hats all around? I would like a decently low ride height.
#37
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
So 5"f and 6"r would be the better option then like stated above. What can the regular Komi sports hold for spring rates front and rear. I was thinking maybe a better option would be to use Komi sports all around with rates of 500-550f and 400r with nb top hats all around? I would like a decently low ride height.
#38
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
I think the longer springs with be the ticket, but I wont rule it out to remove preload from the spring and extend the stroke before bind. but like i said, I'm like ~.5" off.