Rotor not centered in bracket-mtuned kit
#1
Junior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2013
Location: Texas
Posts: 442
Total Cats: 20
Rotor not centered in bracket-mtuned kit
Hey guys. I just mocked up a Mtuned bracket kit to adapt the 10.9 sport rotors. Everything is new. Rotors, mtuned kit, caliper hub bearings...everything. The kit bolts on but the rotor is not centered in the bracket. I see no way to space it out since it’s rubbing on the inside. Any ideas on how to get past this?
The easiest way I can see is to grind down the area of the bracket that is making contact.
Hub/bearing was professionally installed. Torqued to 190 ftlbs.
Rotor or was fully seated and torqued with lug nuts as well.
Any issue grinding the caliper bracket? The contact area does not modify pad placement or retention. I fitted the oem caliper and result was the same. Thanks!
N
The easiest way I can see is to grind down the area of the bracket that is making contact.
Hub/bearing was professionally installed. Torqued to 190 ftlbs.
Rotor or was fully seated and torqued with lug nuts as well.
Any issue grinding the caliper bracket? The contact area does not modify pad placement or retention. I fitted the oem caliper and result was the same. Thanks!
N
#2
Junior Member
iTrader: (1)
Join Date: Jun 2010
Location: Niagara Falls NY/ Ontario, CA
Posts: 163
Total Cats: 8
Shim between the M-tuned bracket and the caliper bracket? Hard to tell if the rotor is seated flat on the hub or if the caliper is pulling it in
IF not(and my eyes are screwing with me, then milling the M-tuned bracket seems like the next best way
IF not(and my eyes are screwing with me, then milling the M-tuned bracket seems like the next best way
#3
Junior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2013
Location: Texas
Posts: 442
Total Cats: 20
Basically the inside of rotor is sitting on the caliper bracket. Shimming it would push the bracket farther out, making more contact and not allowing rotor to seat right. If it was hitting on the outboard side shimming would work fine.
I ended up grinding the area in this picture last night which gave me clearance. It’s still not going to be centered, but since the calipers float I don’t see that as an issue.
Machining the mtuned brackwt would definitely work, I just don’t have the tools to do that properly (mill). If I did it by hand it wouldn’t be flat haha.
I ended up grinding the area in this picture last night which gave me clearance. It’s still not going to be centered, but since the calipers float I don’t see that as an issue.
Machining the mtuned brackwt would definitely work, I just don’t have the tools to do that properly (mill). If I did it by hand it wouldn’t be flat haha.
#12
Junior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2013
Location: Texas
Posts: 442
Total Cats: 20
I tried to put driver to passenger. No way to make it go. Tried to flip and rotate every which way. There is only one way to seat the thing and that’s how I have it. Looks the same as the old mtuned instructions. Maybe the brackets I got were machined a mm too thick. Who knows. Either way I ground the caliper bracket and have full clearance of rotor now so it should be fine. I know the caliper bracket wasn’t different as I tried the oem one and it was the same so it has to be the mtuned piece. Or I’m crazy. That’s always possible
#13
Junior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2013
Location: Texas
Posts: 442
Total Cats: 20
Figured out the variable which caused the centering issue. It’s the axles. I got new manufactured axles. Same manufacturer same part number. They were the same length as stock. Manufactured at different times. The axle ends are machined to different depths which makes them sit slightly different when seated. Weird.
#17
Junior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2013
Location: Texas
Posts: 442
Total Cats: 20
Another thing. The rear bearing dust seal seats against the taper on the 10.3xmm one. On the 15.3x it doesn’t reach the taper.
strangely enough, the longer one had no centering issues...the shorter one, which is roughly the same length as the stock one I pulled out, is the one that had issues centering lol.
Oh well. It’s all good and clearanced just wanted to update my findings.
strangely enough, the longer one had no centering issues...the shorter one, which is roughly the same length as the stock one I pulled out, is the one that had issues centering lol.
Oh well. It’s all good and clearanced just wanted to update my findings.
#18
Another thing. The rear bearing dust seal seats against the taper on the 10.3xmm one. On the 15.3x it doesn’t reach the taper.
strangely enough, the longer one had no centering issues...the shorter one, which is roughly the same length as the stock one I pulled out, is the one that had issues centering lol.
Oh well. It’s all good and clearanced just wanted to update my findings.
strangely enough, the longer one had no centering issues...the shorter one, which is roughly the same length as the stock one I pulled out, is the one that had issues centering lol.
Oh well. It’s all good and clearanced just wanted to update my findings.
#19
Junior Member
Thread Starter
iTrader: (9)
Join Date: Sep 2013
Location: Texas
Posts: 442
Total Cats: 20
Appreciate it. The bearings are fully seated. The shank length is the same on both axles it’s the depth where the taper for wheel seal begins that is a different length. This does not effect the seating of the bearing.
Both axles have the same amount of protrusion out of the torqued axle nut as well.
There is is one other variable. One of the uprights was changed. The original broke an ear off in the press. I threw the original away so I can’t take measurements. I wish I could say exactly what the problem is but I have t been able to pinpoint it.
I did not not shim anything though. I clearanced the inner edge of the bracket after consulting with a trusted mechanic.
Both axles have the same amount of protrusion out of the torqued axle nut as well.
There is is one other variable. One of the uprights was changed. The original broke an ear off in the press. I threw the original away so I can’t take measurements. I wish I could say exactly what the problem is but I have t been able to pinpoint it.
I did not not shim anything though. I clearanced the inner edge of the bracket after consulting with a trusted mechanic.
#20
Appreciate it. The bearings are fully seated. The shank length is the same on both axles it’s the depth where the taper for wheel seal begins that is a different length. This does not effect the seating of the bearing.
Both axles have the same amount of protrusion out of the torqued axle nut as well.
There is is one other variable. One of the uprights was changed. The original broke an ear off in the press. I threw the original away so I can’t take measurements. I wish I could say exactly what the problem is but I have t been able to pinpoint it.
I did not not shim anything though. I clearanced the inner edge of the bracket after consulting with a trusted mechanic.
Both axles have the same amount of protrusion out of the torqued axle nut as well.
There is is one other variable. One of the uprights was changed. The original broke an ear off in the press. I threw the original away so I can’t take measurements. I wish I could say exactly what the problem is but I have t been able to pinpoint it.
I did not not shim anything though. I clearanced the inner edge of the bracket after consulting with a trusted mechanic.
I'm sure I'm just not envisioning what you're trying to explain.