Where the Hell can I find these freaking fittings!? (1/8" BSPT)
#1
Elite Member
Thread Starter
iTrader: (5)
Join Date: Apr 2007
Location: Wellford, SC
Posts: 1,697
Total Cats: 1
Where the Hell can I find these freaking fittings!? (1/8" BSPT)
Been searching around for awhile to find replacement hose barb fittings for my APEXi Boost Solenoid as one was sheared off in an accident. Thought I had found out that they were 1/8" NPT. Everything thread in smoothly until about 4 revolutions, then it got QUITE difficult to turn. After doing some searching I found out that the required fitting is actually a 1/8" BSPT. EFF! Been searching for hours with no luck. Found one place in the UK that wouldn't ship to the US... Checked McMaster as well with no luck. Basically I am looking for a (2) hose barb fittings with 1/8" BSPT male and 3/16" hose barb.
Representative photo:
Representative photo:
#11
!!! NOT CONFIRMED !!!
iTrader: (1)
Join Date: Oct 2008
Location: Cleveland Ohio
Posts: 67
Total Cats: 0
your propably going to have to get a different size barb. I looked as well and it seems that the size your talking about just isn't made. I found some with 5/32 barbed and 1/4 barbed, but nothing in between. Its kinda wierd.
#12
Elite Member
Thread Starter
iTrader: (5)
Join Date: Apr 2007
Location: Wellford, SC
Posts: 1,697
Total Cats: 1
This is UBER close... I will check and see if I can get away with fitting a 1/4" ID hose on a similar fitting. :crosses fingers:
Mitchell, no JB Weld for this reason...Trying to avoid damaging the solenoid or modifying it as I plan to get rid of it once it is fixed... So yes, an APEXi AVC-R will be up in the FS section sometime soonish.
18psi, they were 1/8" NPT at Ace. That's where I got the ones that only thread in 4 rotations.
Brain, you are correct sir...
Mitchell, no JB Weld for this reason...Trying to avoid damaging the solenoid or modifying it as I plan to get rid of it once it is fixed... So yes, an APEXi AVC-R will be up in the FS section sometime soonish.
18psi, they were 1/8" NPT at Ace. That's where I got the ones that only thread in 4 rotations.
Brain, you are correct sir...
Last edited by thagr81 us; 04-07-2010 at 04:00 PM.
#13
Senior Member
iTrader: (4)
Join Date: Jan 2008
Location: Falls Church, VA
Posts: 1,361
Total Cats: 17
LOL no ******* way. You might be able to get it at a local mom & pop hardware store, but you'll have to give pops some hand relief to convince him to special order it, perhaps from jolly old England or wherever they use British pipe thread.
Here's a mcmaster part that may help:
5832T111
3/4" long pipe nipple with 1/8 BPST on one end and NPT on the other. To that you could attach a common 1/8 female NPT barb adapter. Assuming the additional length isn't a problem for your application.
Here's a mcmaster part that may help:
5832T111
3/4" long pipe nipple with 1/8 BPST on one end and NPT on the other. To that you could attach a common 1/8 female NPT barb adapter. Assuming the additional length isn't a problem for your application.
#14
Dude if you get really desperate I'll try the local hydraulic fittings place and see if they can get one, then ship it over to you. PM me the EXACT fitting you need and I'll give them a call.
edit: just re read the original post and I see you have already posted what you are after. Its past 9 in the evening now but ill try calling them in the morning if you like just to see if they have it and how much. Let me know if I should bother.
edit: just re read the original post and I see you have already posted what you are after. Its past 9 in the evening now but ill try calling them in the morning if you like just to see if they have it and how much. Let me know if I should bother.
#15
Elite Member
Thread Starter
iTrader: (5)
Join Date: Apr 2007
Location: Wellford, SC
Posts: 1,697
Total Cats: 1
Dude if you get really desperate I'll try the local hydraulic fittings place and see if they can get one, then ship it over to you. PM me the EXACT fitting you need and I'll give them a call.
edit: just re read the original post and I see you have already posted what you are after. Its past 9 in the evening now but ill try calling them in the morning if you like just to see if they have it and how much. Let me know if I should bother.
edit: just re read the original post and I see you have already posted what you are after. Its past 9 in the evening now but ill try calling them in the morning if you like just to see if they have it and how much. Let me know if I should bother.
#19
Elite Member
Thread Starter
iTrader: (5)
Join Date: Apr 2007
Location: Wellford, SC
Posts: 1,697
Total Cats: 1
Yeah... I thought about selling it like it is. Also, I am fabricating a new mounting bracket for it as well as the other got destroyed in my accident. Just trying to make sure the buyer doesn't have to go through all of these hoops to have a running unit.
#20
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
This is UBER close... I will check and see if I can get away with fitting a 1/4" ID hose on a similar fitting. :crosses fingers:
Mitchell, no JB Weld for this reason...Trying to avoid damaging the solenoid or modifying it as I plan to get rid of it once it is fixed... So yes, an APEXi AVC-R will be up in the FS section sometime soonish.
18psi, they were 1/8" NPT at Ace. That's where I got the ones that only thread in 4 rotations.
Brain, you are correct sir...
Mitchell, no JB Weld for this reason...Trying to avoid damaging the solenoid or modifying it as I plan to get rid of it once it is fixed... So yes, an APEXi AVC-R will be up in the FS section sometime soonish.
18psi, they were 1/8" NPT at Ace. That's where I got the ones that only thread in 4 rotations.
Brain, you are correct sir...