Engine Performance This section is for discussion on all engine building related questions.
Sponsored by:
Sponsored by: KPower

960cc injectors dw300 with td04

Thread Tools
 
Search this Thread
 
Old 03-30-2021, 10:38 PM
  #1  
Newb
Thread Starter
 
nissonoodles's Avatar
 
Join Date: Jun 2020
Posts: 18
Total Cats: 0
Default 960cc injectors dw300 with td04

I've got the parts. Someone talk me out of it...
nissonoodles is offline  
Old 03-31-2021, 05:39 AM
  #2  
Junior Member
iTrader: (1)
 
adryargument's Avatar
 
Join Date: Dec 2015
Location: Brisbane
Posts: 246
Total Cats: -20
Default

sounds fun. go for it.
adryargument is offline  
Old 04-01-2021, 11:40 AM
  #3  
Junior Member
 
Dyladjent's Avatar
 
Join Date: Mar 2018
Location: Montevallo, AL
Posts: 100
Total Cats: 10
Default

Depending on what manifold/exhaust housing you use its going to be 100% custom. I have over 3k in just a turbo, dp and exhaust setup. My case is a tad unusual because I have a top mount manifold and I wanted a full 3" DP and my turbo has a really odd 4 bolt turbine housing. If I were to do it again I'd probably just go with a side mount t25 setup using a downpipe that is already available. So depending on your turbo/manifold combo it may be relatively easy or really hard for not much payoff over another more commonly used setup. If you do decide to go with the td04 there are tons of upgrade options for different power goals though. I'm waiting on my custom td04hl-16t to come in now.

Also unless you have a built engine and a big 19t compressor wheel you will be fine with the stock fuel pump. There are conflicting opinions but going to a higher output pump, depending on your setup, could result in some problems with fuel pressure and overwhelming your regulator. I make all the power my stock rods can handle on 93 and the stock pump with 650cc FF injectors. YMMV.
Dyladjent is offline  
Old 04-22-2021, 02:00 PM
  #4  
Newb
Thread Starter
 
nissonoodles's Avatar
 
Join Date: Jun 2020
Posts: 18
Total Cats: 0
Default

Originally Posted by Dyladjent
Depending on what manifold/exhaust housing you use its going to be 100% custom. I have over 3k in just a turbo, dp and exhaust setup. My case is a tad unusual because I have a top mount manifold and I wanted a full 3" DP and my turbo has a really odd 4 bolt turbine housing. If I were to do it again I'd probably just go with a side mount t25 setup using a downpipe that is already available. So depending on your turbo/manifold combo it may be relatively easy or really hard for not much payoff over another more commonly used setup. If you do decide to go with the td04 there are tons of upgrade options for different power goals though. I'm waiting on my custom td04hl-16t to come in now.

Also unless you have a built engine and a big 19t compressor wheel you will be fine with the stock fuel pump. There are conflicting opinions but going to a higher output pump, depending on your setup, could result in some problems with fuel pressure and overwhelming your regulator. I make all the power my stock rods can handle on 93 and the stock pump with 650cc FF injectors. YMMV.
Thanks!
My current td04-13t setup is already built, I was toying around with the idea of seeing what parts I could install before rebuilding with my forged internals and 3071.

For posterity my results ended up with: Td04-13t, the 960's and the stock (but new) fuel pump. The 300 was causing weird fuel fluxuations because of the nb's lack of a proper FPR. I ended up picking up more midrange power just by allowing myself some more overhead in my injectors. I was coming from rx-8 yellow tops @420cc. The injectors @nigelt sent me ended up being much larger than expected by about 20cc @3bar, and finalized with an average of 1151cc @4 bar. Once I get a proper AFPR I'll swap in the dw300 pump for future-proofing reasons.
nissonoodles is offline  
Old 04-22-2021, 06:45 PM
  #5  
Retired Mech Design Engr
iTrader: (3)
 
DNMakinson's Avatar
 
Join Date: Jan 2013
Location: Seneca, SC
Posts: 5,009
Total Cats: 857
Default

Keep the stock, but new pump until you build the motor and get a bigger turbo.

DNMakinson is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
TURNS101
Miata parts for sale/trade
35
01-12-2012 01:15 AM
3barboost
DIY Turbo Discussion
5
11-09-2008 10:46 AM
cjernigan
DIY Turbo Discussion
32
03-01-2007 12:04 PM



Quick Reply: 960cc injectors dw300 with td04



All times are GMT -4. The time now is 08:12 AM.