Innovate AFR readings off
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Apr 2010
Location: Gulf Breeze Fl
Posts: 108
Total Cats: 0
Innovate AFR readings off
MS2/Innovate Nightmare
04 msm
650cc fic
MS2 enhanced
Innovate wb02
So the car idles fine at with an AFR value anywhere from 14.1-14.9. But TunerStudio only reads the value at 10-11. I assume this is why I cannot run autotune successfully within TS. I have a few data logs of it while its idling good at 14.7 (according the the innovate gauge) but as soon as I start to drive with autotune it kinda turns to ****. Is it correct to assume that the innovate gauge is accurate, and the reading tunerstudio is getting is off?
I have the innovate grounded at the same spot as the stock ecu, but not the same point of origin, right next to the throttle body with its own wire.
04 msm
650cc fic
MS2 enhanced
Innovate wb02
So the car idles fine at with an AFR value anywhere from 14.1-14.9. But TunerStudio only reads the value at 10-11. I assume this is why I cannot run autotune successfully within TS. I have a few data logs of it while its idling good at 14.7 (according the the innovate gauge) but as soon as I start to drive with autotune it kinda turns to ****. Is it correct to assume that the innovate gauge is accurate, and the reading tunerstudio is getting is off?
I have the innovate grounded at the same spot as the stock ecu, but not the same point of origin, right next to the throttle body with its own wire.
#4
Elite Member
iTrader: (16)
Join Date: Oct 2006
Location: Las Cruces, NM
Posts: 1,647
Total Cats: 524
I have the Innovate MTX-L and the enhanced DIYPNP. Try using custom linear wideband and use the values:
0.2v - 7.3 afr
5.0v - 20 to 22 afr
I was able to get them to match perfectly. Make sure to open-air calibrate the wideband sensor first.
0.2v - 7.3 afr
5.0v - 20 to 22 afr
I was able to get them to match perfectly. Make sure to open-air calibrate the wideband sensor first.
#7
Elite Member
iTrader: (1)
Join Date: Jun 2006
Location: Warrington/Birmingham
Posts: 2,642
Total Cats: 42
By default the yellow wire of the LC-1 is set-up as a simulated narrowband output i.e. only 0-1v
http://www.innovatemotorsports.com/s...C-1_Manual.pdf - Page 4 step 6, I'm guessing you didn't read the install instructions....
You can reconfigure it in LM-Programmer as a 0-5v output very quickly though.
http://www.innovatemotorsports.com/s...C-1_Manual.pdf - Page 4 step 6, I'm guessing you didn't read the install instructions....
You can reconfigure it in LM-Programmer as a 0-5v output very quickly though.
#8
Junior Member
Thread Starter
iTrader: (1)
Join Date: Apr 2010
Location: Gulf Breeze Fl
Posts: 108
Total Cats: 0
I have tried everything and cant think of anything else I can try. Its still doing the same thing with tunerstudio not getting an accurate reading.
Afr Wont Display On Tuner Studio? - Forced Induction & N/A Power Mods - MX5Nutz Forum
ive tried everything in that thread too, but with no change.
changing the settings to lambda didnt do anything, nor did changing them to afr. and changing it to a 0-5v output didnt do anything either.
any more advice?
Afr Wont Display On Tuner Studio? - Forced Induction & N/A Power Mods - MX5Nutz Forum
ive tried everything in that thread too, but with no change.
changing the settings to lambda didnt do anything, nor did changing them to afr. and changing it to a 0-5v output didnt do anything either.
any more advice?
#12
Junior Member
Thread Starter
iTrader: (1)
Join Date: Apr 2010
Location: Gulf Breeze Fl
Posts: 108
Total Cats: 0
yes i have set the outputs in lm programmer, and it didn't change anything. it would change the value tunerstudio got, but it would be stuck at whatever value it would change to.
and it would still not match the value the innovate gauge was reading.
and it would still not match the value the innovate gauge was reading.
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM