12 tooth crank trigger settings?
#1
12 tooth crank trigger settings?
Hey guys...
I just bought a 12 tooth wheel to use with my AEM on my 94.
Can anyone who is using this wheel share their cal file?
I know I need to set the fuel teeth to 12, the ign range to 1.5 teeth... what else?
FWIW, I plan on using the OEM 1994 4-tooth cam/crank sensor for sync. Do I need to mod the cam sensor too?
Many thanks
I just bought a 12 tooth wheel to use with my AEM on my 94.
Can anyone who is using this wheel share their cal file?
I know I need to set the fuel teeth to 12, the ign range to 1.5 teeth... what else?
FWIW, I plan on using the OEM 1994 4-tooth cam/crank sensor for sync. Do I need to mod the cam sensor too?
Many thanks
Last edited by lukydvll; 08-01-2010 at 03:51 PM.
#2
fuel teeth = 24
Ign range is 90*, which is 3 teeth, not 1.5.
There are several other setting which have "teeth" as units. For example MAP sensor filtering now needs to be at 6. Also check (IIRC) dwell MAX, which now should be 5 teeth.
No need to mod the cam sensor. Be sure you are moving the CKP signal to the crank, and not the CMP signal.
The cam/crank setup needs to be changed in many other ways.
More later.
Ign range is 90*, which is 3 teeth, not 1.5.
There are several other setting which have "teeth" as units. For example MAP sensor filtering now needs to be at 6. Also check (IIRC) dwell MAX, which now should be 5 teeth.
No need to mod the cam sensor. Be sure you are moving the CKP signal to the crank, and not the CMP signal.
The cam/crank setup needs to be changed in many other ways.
More later.
Last edited by JasonC SBB; 08-01-2010 at 07:08 PM.
#5
Elite Member
iTrader: (22)
Join Date: Dec 2006
Location: Sunny Spanish speaking Non US Caribbean
Posts: 3,224
Total Cats: 3
#6
Thanks for the reply Jason.
I see... 720 degrees of crank = 24 teeth per engine cycle.
So I could trigger the coils (wasted spark) at say, 0 and 12 teeth, and fire the injectors at 0, 6, 12, 18 teeth... correct?
Another question. Should I be triggering on rising edge only with this new 12-tooth wheel?
Oh, it is the trackspeed piece.
I see... 720 degrees of crank = 24 teeth per engine cycle.
So I could trigger the coils (wasted spark) at say, 0 and 12 teeth, and fire the injectors at 0, 6, 12, 18 teeth... correct?
Another question. Should I be triggering on rising edge only with this new 12-tooth wheel?
Oh, it is the trackspeed piece.
#7
Elite Member
iTrader: (22)
Join Date: Dec 2006
Location: Sunny Spanish speaking Non US Caribbean
Posts: 3,224
Total Cats: 3
Thanks for the reply Jason.
I see... 720 degrees of crank = 24 teeth per engine cycle.
So I could trigger the coils (wasted spark) at say, 0 and 12 teeth, and fire the injectors at 0, 6, 12, 18 teeth... correct?
Another question. Should I be triggering on rising edge only with this new 12-tooth wheel?
Oh, it is the trackspeed piece.
I see... 720 degrees of crank = 24 teeth per engine cycle.
So I could trigger the coils (wasted spark) at say, 0 and 12 teeth, and fire the injectors at 0, 6, 12, 18 teeth... correct?
Another question. Should I be triggering on rising edge only with this new 12-tooth wheel?
Oh, it is the trackspeed piece.
I'm sure Jason will post additional info. He said it in his post.
#8
Before I make a mistake, I will wait for J_Man to post up his cam/crank setup, because he's had his 12T wheel running.
Mine will be a modification of his, as I will be modding it into a 12-1, due to my VVT.
P.S. The tooth table should be all 5's from 0 to 23, then a 3 at 24, then all 0's.
For a 12-1 it should all 5' from 0 to 11, then 3, then 0's.
Mine will be a modification of his, as I will be modding it into a 12-1, due to my VVT.
P.S. The tooth table should be all 5's from 0 to 23, then a 3 at 24, then all 0's.
For a 12-1 it should all 5' from 0 to 11, then 3, then 0's.
#9
If anyone is looking for this info themselves, J_Man posted the settings needed to use the 12-tooth wheel here:
http://forum.miata.net/vb/showthread...43#post4688943
Thanks for the help people
http://forum.miata.net/vb/showthread...43#post4688943
Thanks for the help people
Thread
Thread Starter
Forum
Replies
Last Post
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM
Mikel
MEGAsquirt
4
09-28-2015 04:46 PM