Never ever coat the inside of a turbo manifold, especially with a ceramic coating. You don't want to chance anything peeling off and hitting the turbine blades.

Got some lame videos. tuned enough to run and be safe, but really just for shits and giggles more. wont do anything else now until im back.

Set my suspension today...ride height, preload, etc etc. Going to get alignment tomorrow, hopefully.

Also went WOT for the first time..video below. its just WG pressure, about 10psi or so, non-intercooled.. Not really tuned at all, just wanted to see how it would do. Once I get the intercooler stuff done I will start really going at it with the tune (AND TURN UP THE BEWST!!)

Attachment 190065

Attachment 190066

Attachment 190067

Attachment 190068

Looking good! Grats on boost!

Looks like that nice warm weather you have helps nullify wheelspin haha

Welcome back. Be careful with that 10psi stuff until you have either WI or intercooling. Looking forward to seeing you finish this thing (oh yeah, they're never finished, are they?).

After viewing datalogs..looks like I got up to like 14psi for a split second.. looks like boost creep or something. Kinda scratching my head over this one, I will play around with the WG preload some.

Either way I only did WOT a few times in short spurts, but definitely going to take it easy until I get IC and meth on this weekend...hopefully then it will be pretty much done, other than tuning.

Very nice. How are you liking the open dump tube?

I was a little worried at first that it would leak at idle/cruise and sound like crap...but it's not at all so I am very happy...gotta have my rice factor!!

moved radiator and mounted up the IC and stuff today...been a long day, but really happy with how it all came out. It was dark when we finished, so only have a few crappy pics. Better ones to come tomorrow.

Attachment 189956

Attachment 189957

Attachment 189958

Attachment 189959

Moving the radiator. That's cool. Have others done this? I haven't seen this before (maybe I just wasn't paying attention).

I did that on my 1st setup too. Not bad, but make sure you shroud the top or you're going to have really shitty airflow to the rad

hornetball, you have an NA, it's much harder. The NB is screaming to have it's radiator tilted back with simple strips of metal.

Yeah, it really was not bad at all. Anyone who buys the TDR intercooler kit for NB is a tard lol.

For the stock brackets (i should have taken a pic...).. You just have to elongate one of the holes, and for the other, i slightly elongated it diagonally so i could tilt it back a little as well. There's bolts right below where the brackets mount, it works out really really well. I used the TDR instructions to help me out along the way if I wasn't sure about something.

Have intake.... but now that I've actually gotten on it, I'm definitely getting boost creep. Kicking myself for not getting EWG now... not sure if I am going to go EWG route, or send turbo off to get IWG ported. Seems like everyone with GT2560R who had any creep...porting from Begi fixed everything (and I saw a post from 2008 they offered to do it for free for ANY Garrett turbo...wonder if they are still doing that).

I checked range of motion of the WG flapper-fine. Actuated the WG with air compressor-fine, doesn't limit movement at all. No pre-load at all...and just running WG pressure (7psi actuator), with the source as the turbo comp outlet. FYI the datalog is 2nd gear...but I do have sorta long gearing- 5 spd, 3.909 rear end.

Attachment 189945

Attachment 189946

I like the small intercooler. Oversized intercoolers hurt.

still boost creeping, but got some pics today!!

Attachment 189660

Attachment 189661

Attachment 189662

Attachment 189663

Attachment 189664

Still creeps up top...but i 'fixed' that by just running 16 psi across the board :) lol.

Got it tuned pretty well today and consistent at or around 15-16 psi... Also, this is what happens when you park your other car too close the exhaust of the miata lol.

Attachment 189515

Attachment 189516

Your CLT is jittery as hell.

Camera fail on my end... didn't get the speedo too well on the 2nd half of the video, was more focused on the road and shifting I guess. 3rd tops out at something like 92mph. (5 speed, 3.9 gearing)

Was out of town for 2 weeks, just got back and starting playing with the car again. Boost is pretty good at 15-16 psi, but only if I work the throttle a certain way. Drag race style, thru the gears I don't overboost at all and it's great...problem arises when I'm in part throttle boost...lets say 10 psi, then I go WOT, it will WAY overshoot and hit boost fuel cut (18 psi) instantly, then after that it will settle down to target. I have a feeling this inconsistency is ultimately because my car can't control boost that well. It's pretty annoying, I didn't notice it today until I found some 'decent' curvy backroads etc.... on the street never had the part throttle to WOT overboost issue.

Also got another speedo vid thing, but I forgot my camera...so this is my phone...it's kinda fail. It randomly skips at the beginning, I guess the incredible acceleration messed the phone up (lol)... went all the way from a stop to top of 4th gear... this sort of scenario it's running well. Note that my drivetrain still thinks I'm running the standard 4.3 rear diff, when I really have 3.9, so my speedo is pretty far off, especially at higher speeds. 3rd tops out around 92 mph, 4th around 122 (speedo over 10 mph off at 100+)

http://i165.photobucket.com/albums/u...507_190441.jpg