the new thing must be to buy the bad, grab the goods, and have curly cut it up.
|
Naw, I won't bother curly with this one. I've got a sawzall :)
|
4 Attachment(s)
|
That auction car is an '01 SE, hence the BRG. It would have the 6 speed and 3.9 unless that's been swapped by a PO.
Curious to see how much it goes for. |
Originally Posted by turbofan
(Post 1232853)
That auction car is an '01 SE, hence the BRG. It would have the 6 speed and 3.9 unless that's been swapped by a PO.
Curious to see how much it goes for. |
|
No idea why, it doesn't show up when I do a wastegate run but it needs it in closed loop. I'll post up my bias duty table in a bit.
|
That is strange, did we tune the same thing on the dyno with open loop? Aka: higher duty at that RPM?
|
1 Attachment(s)
Nope but its pretty much required if I want flat boost. Also the boost is smoother now than it was on they dyno I believe.
Here is our most powerful dyno pull: Attachment 237764 Peaked at 200ish, then dropped to 187 at around 5250 rpm. Right where that spike of duty is needed. |
What the shit dude!? No more truck project? My life is over!
(Melodrama caused by beer coming to a mailbox near you soon.) |
The house we were going to move into got vandalized a second time and they are taking it off the market. It had a big driveway/yard and tons of room and no neighbors. Truck project will happen, just not as soon as I wanted it.
|
1 Attachment(s)
<p>Out in 57 minutes, new record, I'm coming for you <span>@curly.</span></p><p> </p><p>Attachment 237760</p>
|
what happened?
|
Upgrading the diff bushings?? What ever you do don't burn them. It doesn't work as well as people claim.
|
I was able to use a punch and hammer to beat mine out of the housing, but don't you have to burn them off the lower mounts?
|
Maybe for poly mounts. I used delrin from garagestar and they say you leave the lower alone.
|
1 Attachment(s)
Originally Posted by ScottyP3821
(Post 1233925)
Upgrading the diff bushings?? What ever you do don't burn them. It doesn't work as well as people claim.
Originally Posted by ScottyP3821
(Post 1233930)
Maybe for poly mounts. I used delrin from garagestar and they say you leave the lower alone.
Originally Posted by deezums
(Post 1233928)
I was able to use a punch and hammer to beat mine out of the housing, but don't you have to burn them off the lower mounts?
|
2 Attachment(s)
<p>Yes diff mounts. And holy fuck they are stuck. All the rubber is burned out and I have them peeling off the housing. But they are rusted inside there. My 1.6 mounts were no where near as hard to get out as these.</p><p>I only have garagestar for now, I will make my own lower mounts at some point.</p><p>Here's where I'm at right now.</p><p>https://www.miataturbo.net/attachmen...ine=1432319667<br />https://www.miataturbo.net/attachmen...ine=1432319667</p>
|
1 Attachment(s)
<p>I was going to make my own but I'm going to the drag strip this weekend and need to get rid of some of the nasty wheel hope I got when I upgraded tires.</p><p> </p><p>https://www.miataturbo.net/attachmen...ine=1432320034</p>
|
Oh dear. Mine basically slipped right out. Good luck sir.
|
All times are GMT -4. The time now is 08:46 PM. |
© 2024 MH Sub I, LLC dba Internet Brands