Yup plus it devalues your image having not so perfect product out in the market. What if someone saw the frame without finding out the back story?
Same reason I don't sell damaged or old bread. And no, I don't throw it away. The women's shelter or homeless shelter gets it. |
Originally Posted by 18psi
(Post 1172892)
the stupid shippers learn a valuable lesson that will motivate them to be more careful next time
What's wrong is that's basically a perfectly good frame that is going to get scrapped for BS tax reasons. Government make believe that cause REAL things to get destroyed for no good reason. "We" had to crush two perfectly good race cars for similar tax law foo foo a couple years back. Whateves |
Hah, where did you guys get the idea it was going to get scrapped? Don't worry, seems like everyone is begging for a piece of that frame...
The damage wasn't structural, it just scratched the powdercoat on top and dented a tube that gets covered by the rear tank cover anyways. Don't worry, we'll make sure it goes to a nice home. :) |
I already called dibs
|
Originally Posted by dutchbag
(Post 1174435)
Hah, where did you guys get the idea it was going to get scrapped? Don't worry, seems like everyone is begging for a piece of that frame...
The damage wasn't structural, it just scratched the powdercoat on top and dented a tube that gets covered by the rear tank cover anyways. Don't worry, we'll make sure it goes to a nice home. :) |
2 Attachment(s)
UPS Just messed mine up too! Not as bad, but after reading this thread, I inspected it before it left the truck:
https://www.miataturbo.net/attachmen...ine=1414549089 https://www.miataturbo.net/attachmen...ine=1414549089 If it were on a lower tube, I would have probably accepted it, but not where I have to see it getting in/out. |
I guess we found out what Brown could do for us. :crx:
These recent damages are utterly ridiculous. Do they have lemmings driving the forklifts? |
I'm sure they're laughing at us too though.
"How hard can it be to transport a giant car chassis barely wrapped in a layer of plastic across the country?!" |
Originally Posted by dutchbag
(Post 1179343)
I guess we found out what Brown could do for us. :crx:
These recent damages are utterly ridiculous. Do they have lemmings driving the forklifts? I have given up hope in any of our postal services long ago - pack well and insure for a VERY large amount. |
Just place some 2x4's on top of the frame and band them in place to act as a sacrificial element. Problem solved.
|
Sucks about the damage, I would have sent it back too.
|
Car finial showed up without UPS fucking it up do to it not shipping UPS.
Photos on Facebook page and to lazy to post them all. http://oi60.tinypic.com/2b1end.jpg |
Originally Posted by jeff_man
(Post 1161699)
Lots of photos and info will be posted to https://www.facebook.com/NMHFR
We are working with Hanchey Vehicle Tech to get the most out of the frame. Yes there is currently a MP62 in the build but will be switching to a build VVT or k20/24 once we figure out power to weight and points for TT classing. Current goal is TT3 with over head in the motor to bump up easily. Update Car is here http://oi60.tinypic.com/2b1end.jpg Stuck with a stock miata motor that I had my mp62 on do to the cost and how much extra time it would take to get, install, brake, figure out a K swap. |
Sounds good Jeff, we are here to help.
|
Once you get it in the air could you take some pictures of the underside. Which stock exhaust do you use, a NA or NB?
|
Originally Posted by shuiend
(Post 1184617)
Once you get it in the air could you take some pictures of the underside. Which stock exhaust do you use, a NA or NB?
I have a RB header and a custom made ArTech midpipe back. Will likely take the car back to ArTech and have him make the axle back part fit under the exocet rear deck better as the rear of the car is about a ft shorter. For now it will be a open mid pipe till I can get it over to him. What exactly are you looking for on the underside? |
Originally Posted by jeff_man
(Post 1184668)
What exactly are you looking for on the underside?
|
1 Attachment(s)
What do you plan on racing with? Hopes and dreams?
https://www.miataturbo.net/attachmen...ine=1416871297 |
Originally Posted by shuiend
(Post 1184863)
Where the mounting points for exhausts are, and general late out. Basically I am trying to figure out if my turbo exhausts will bolt right up, or if I will have to modify them to fit an exocet.
--Ferdi |
|
All times are GMT -4. The time now is 10:37 PM. |
© 2024 MH Sub I, LLC dba Internet Brands