downpipe bends
#1
Elite Member
Thread Starter
iTrader: (24)
Join Date: Jun 2007
Location: Woodland Hills, CA
Posts: 4,667
Total Cats: 18
downpipe bends
so... im looking for a template of some sort or perhaps a list of bends used to make a downpipe for a miata... anyone has anything? i bet it will make a great sticky thread if someone actually has something
#2
Elite Member
iTrader: (5)
Join Date: Jul 2006
Location: Central California
Posts: 2,546
Total Cats: 4
well the begi-s looks like a 90* coming out of turbine followed by a 45*. Then to clear the transmission flange while not hitting the firewall, it looks like theres an s-bend made of two 45*s and then straight back including the flex bellow to the cat.
Only thing i think i want around for the build is a miter saw with a cuttoff wheel so i can get straight cuts when i finetune the fittment. Something to expand the pipes a bit would be super sweet too. Then tack it up and have a shop weld it up.
Only thing i think i want around for the build is a miter saw with a cuttoff wheel so i can get straight cuts when i finetune the fittment. Something to expand the pipes a bit would be super sweet too. Then tack it up and have a shop weld it up.
#3
Elite Member
Thread Starter
iTrader: (24)
Join Date: Jun 2007
Location: Woodland Hills, CA
Posts: 4,667
Total Cats: 18
i cant weld for **** so ill just duct tape it and will have shop weld it for me
so... what bends should i get? 1x 90* and 3x 45* + 10' of straight? i think im gonna grab a U pipe as well while im at it in case i need some weird angle or something... this will be fun and will involve a LOT of duct tape...
so... what bends should i get? 1x 90* and 3x 45* + 10' of straight? i think im gonna grab a U pipe as well while im at it in case i need some weird angle or something... this will be fun and will involve a LOT of duct tape...
#4
I was planning on doing something like this. I have the top part of an old FM pipe that gives me a short 90degree bend from the turbo, to clear the firewall. Ill be using these connectors http://store.summitracing.com/partde...5&autoview=sku To adjust the size from 2.25 > 2.5 > 3". Right now im still not sure if im gonna go with either a cutout or a complete exhaust. http://store.summitracing.com/partde...5&autoview=sku Was thinking this thing which will do the 2.5">3.0">2.5 to stock cat. Also thinking of an electrical cutout for a fraction of the cost of a true 3".
#13
Elite Member
iTrader: (11)
Join Date: Jun 2007
Location: Overland Park, Kansas
Posts: 5,360
Total Cats: 43
I'm betting on 1 90 degree, along with 2 45 degree bends..
but just in case, I bought an assortment of 10 misc bends in 3" mandrel aluminized. Once I get a good one fabbed up I might make it out of stainless, if I can get access to a TIG welder and figure out how to use one again... Don't think its quite like riding a bicycle...
but just in case, I bought an assortment of 10 misc bends in 3" mandrel aluminized. Once I get a good one fabbed up I might make it out of stainless, if I can get access to a TIG welder and figure out how to use one again... Don't think its quite like riding a bicycle...
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM