2 Attachment(s)
Originally Posted by EO2K
(Post 1167821)
So it runs better on 3 than it does on 4?
/boggle Cyl #4 https://www.miataturbo.net/attachmen...ine=1410987532 Spark plug #4 https://www.miataturbo.net/attachmen...ine=1410987532 |
time for comp/leakdown test
|
1 Attachment(s)
https://www.miataturbo.net/attachmen...ine=1411012908
I then tested spark. Fun little tool in MS I must say. Played with dwell and rpm. #4 spark plug is very shitty spark. All the others were spot on. I increased dwell and it cleared up some carbon and made #4 spark well but the engine still runs like shit. I should of switched the plug around to test. Tomorrow I'm going to compresson test ALLOFTHEM and probably replace the plugs with IK22's or BKR7Es that are cut to fit the coils. Interesting fact: I found another plug to use besides BKR7E's where the insulator and actual end are different. Same 7 heat range but doesn't come out as far. The v8 drag guys use them here. Here's the part number and link for info. NGK 4091 R5671A-7 Racing Plug |
can you please tell me in what universe comp testing 1 cylinder alone has any meaning whatsoever?
do you seriously never do anything properly? you literally half ass EVERY single thing you do. lol don't take this the wrong way, I'm not even mad. its just really amusing |
Originally Posted by 18psi
(Post 1168160)
can you please tell me in what universe comp testing 1 cylinder alone has any meaning whatsoever?
do you seriously never do anything properly? you literally half ass EVERY single thing you do. lol don't take this the wrong way, I'm not even mad. its just really amusing And fuck mosquitos. hard. sideways. Haha, I never have time for shit these days, nor the patients. |
Originally Posted by Impuls
(Post 1168161)
Listen here bitch. :dealwithit: It was 11pm at night and I wanted to be sure the cylinder has compression.
And fuck mosquitos. hard. sideways. Haha, I never have time for shit these days, nor the patients. are you a doctor? |
Originally Posted by 18psi
(Post 1168164)
:laugh: patients?
are you a doctor? You wanna fuck? |
4 Attachment(s)
I thought so.
So, I'm having an awesome day. Car didn't start now, laptop won't connect to MS, and I'm not liking my compression numbers right now. I expect the starting problem is from flooded cylinders of seaform so I'm letting them "air out" Time to a leakdown test. JUST TO MAKE VLAD HAPPY: https://www.miataturbo.net/attachmen...ine=1411147682 https://www.miataturbo.net/attachmen...ine=1411147682 https://www.miataturbo.net/attachmen...ine=1411147682 https://www.miataturbo.net/attachmen...ine=1411147682 |
So, it does seem like cyl 4 is a little bit sad... What did the leakdown test show? Or are you just saying it's time for a leakdown test now that you properly did a compression test?
|
lol I think he called the comp test a leakdown test
he just loves it when I correct all his mis-types and posts :giggle: yeah, doesn't look too good, bummer. I'm guessing that's a low reading tester too, but still doesn't change the fact that there is a 20% variation in #4 |
did you even do the compression test with WOT?
|
Originally Posted by turbofan
(Post 1168604)
So, it does seem like cyl 4 is a little bit sad... What did the leakdown test show? Or are you just saying it's time for a leakdown test now that you properly did a compression test?
|
Swapped in some IK22's.
Started up fine. Did some seafoam, and found the manifold/turbo flange gasket blew out. So time to remove that gasket anyways the flanges were already trued so it was kinda pointless to have the gaskets. Drove the car around and it runs pretty lean anywhere in WOT load, So I didn't do many pulls though. |
aren't you supposed to run the comp test with a warm engine?
your rings won't seal as good with them cold. also, throw in some oil and see if comp gets better. |
Originally Posted by Impuls
(Post 1168935)
Swapped in some IK22's.
Started up fine. Did some seafoam, and found the manifold/turbo flange gasket blew out. So time to remove that gasket anyways the flanges were already trued so it was kinda pointless to have the gaskets. Drove the car around and it runs pretty lean anywhere in WOT load, So I didn't do many pulls though. Yup. |
Originally Posted by Alejo_NIN
(Post 1169295)
aren't you supposed to run the comp test with a warm engine?
your rings won't seal as good with them cold. also, throw in some oil and see if comp gets better. It's probably why the compression numbers were so low. It runs now but has misfire still going to gap down the plugs more. Do a warm compression test and get around to this leak down. About the oil thing. Supposedly, the Mystery Oil stuff works best to do that. An engine builder was saying instead of the seafoam(I was using to clear up carbon) use it and it's what all the guys around here are doing. Helps the rings seal or something. |
He meant put oil in they cylinders during the compression test to see if it brought the numbers up. ATF works better than MMO if you're trying to do a top end ring soak.
|
2 Attachment(s)
Originally Posted by Leafy
(Post 1169421)
He meant put oil in they cylinders during the compression test to see if it brought the numbers up. ATF works better than MMO if you're trying to do a top end ring soak.
So warm compression numbers are here and not looking any better. :/ Attachment 184672 Also got a video of the now very shitty idle and smoke out the exhaust(when rpms decrease) meaning valve/seals, correct? Also have video's of how it doesn't like blipping the throttle or increasing the rpms. |
that motor needs to come out and apart.
|
you blew that engine..
|
All times are GMT -4. The time now is 08:12 AM. |
© 2024 MH Sub I, LLC dba Internet Brands