Holy crap you guys are awesome...thanks for the information. Looks like I will be going megasquirt in a month or so then. Thanks for all your help once again and I will keep this thread updated. Thanks guys!
|
Originally Posted by Saml01
(Post 187461)
You can find TunerToys in the vendor section, they have a T that we can use on our cars that they make for Hondas. I got one and its a nice piece, best of all 21 shipped.
|
Can anyone direct me to a link showing how to run my Charge piping to my FMIC. The intercooler is sort of small, but it is a longer version with the inlet/outlet horizontally parallel with each other. I am @ work or else I would post up pics and measurements. It will be going on a NB, all I can find are links for NA's or NB routing throught the top with the radiator pushed back. Thanks
|
not sure i understand, but i guess just check out these pics
also, are you doing your own IC route or did your Kit come with some? http://i134.photobucket.com/albums/q...Picture071.jpg http://i134.photobucket.com/albums/q...Picture070.jpg http://i134.photobucket.com/albums/q...Picture068.jpg http://i134.photobucket.com/albums/q...Picture067.jpg see if that helps you, this is a DIY set up the piping can differ in a few ways though, so i cant help you there without seeing what you have... GL |
Thanks, yah I will try to get some pictures up tonight. It came with a couple of bends, but the previous owner sold the BOV with a piece he cut from the set up. I know its hard to explain so I will try to post up pictures tonight. But where would I get those brackets, is it all just custom fabircation using pieces from a metal supplier? Also, do I just have to remove the front bumper to access that area or is it much more. Thanks for the pictures, and that looks to be my IC type.
|
its an ebay intercooler and "cuztom bracketz" yo, haha
well, the brackets were actually kinda easy to make, just bought some 1" wide aluminum from home depot and then just cut to length and bend to desired angle, do not over bend it cause aluminum does not like to be corrected...the holes where the brackets bolt up to the car were already there...you'll see once you take the bumper off, its really easy, just use common sense, the bottom ones just get the idea from this pic. i also used some rubber spacers to help longevity... http://i134.photobucket.com/albums/q...Picture071.jpg the car in pictures has both AC and PS so you should be OK if you have those as well and please list your location in your profile... |
Fashizzle... looks like you bought it at FM. All you need to do is round off the bombass edgez yo! Change your correction factorizzle to 1.21 on your next dyno run and you'll be making JDM power.
Mark |
:)
Thanks for the info! |
For my situation, might it be easier just to purchase a voodoo box?
|
go ahead, waste more of your money...
|
Originally Posted by whaaamx5
(Post 188637)
go ahead, waste more of your money...
wideband 180 MS 340 Cas 100 620 vs. the 415 for a Voodoo box seems cheap...someone show me where I am going wrong, I believe I am way too new to my miata's ECU/FMU. |
look at it this way
do it right=MS 350+wideband 180+CAS 75ish=appx$600 do it wrong=voodoo 415, and then MS 350+wideband 180+CAS 75ish=appx$1015 so it is safe to say that: cheaper way=do it right the first time now you get it... |
Hey, I have a 99 as well and my stock ecu controls the 330cc injectors that I have in there . You might be a little rich but you will be able to drive your car instead of waiting to figure out your management issues.
|
Originally Posted by sickmiata09
(Post 188804)
Hey, I have a 99 as well and my stock ecu controls the 330cc injectors that I have in there . You might be a little rich but you will be able to drive your car instead of waiting to figure out your management issues.
|
With the larger injector you need a wideband too...
Listen to those guys here... They really know what they are doing. After 6 psi you want 8 -- 10 --12 psi ... So do it right... 1st time.. |
Im running 8psi with a front mount with no detonation.
|
Thanks guys,
For the oil tee is the BSP side male and the other two female? Please advise asap, I cannot find a solid answer and I am going to a pipe store today to create the tee...thanks |
Most non specialty pipe stores don't carry BSP threaded fittings, it's just not a common fitting here. FWIW
You want a male BSP fitting, that converts into 2 1/8" NPT female fittings. You could just buy the tunertoys one. It's around $21 shipped and it works perfect. |
Originally Posted by cjernigan
(Post 189306)
Most non specialty pipe stores don't carry BSP threaded fittings, it's just not a common fitting here. FWIW
You want a male BSP fitting, that converts into 2 1/8" NPT female fittings. You could just buy the tunertoys one. It's around $21 shipped and it works perfect. |
Originally Posted by 99NBMia
(Post 189323)
Thanks, but I am wondering why everyone says its BSP. If the thread is BSP into the block than wouldn't the OPS be BSP as well, seeing that its already in the block. If true than wouldn't that make one of the females BSp and not NPT? :confused:
You just have to use your brain when it comes to things like that, there are always people giving out info that might pertain to them only. In my case, my stock BSP OPS went in the trash. |
All times are GMT -4. The time now is 09:18 AM. |
© 2024 MH Sub I, LLC dba Internet Brands