WGA to compressor housing...why?
#1
WGA to compressor housing...why?
Ok, so I know on internally gated turbos, everyone runs a rubber line from the WGA to the compressor housing to manage pressure. My question is...with the fluxuation provided from heatsoak, intercooler temperature and density changes, why not run the line to measure boost pressure at the intake manifold where it undergoes no further changes before entering the engine? It just seems like you'd want to adjust your wastegate to read the actual pressure you are sending into the motor, and not the pressure that the turbo is creating.
Someone educate me!
-Nate
Someone educate me!
-Nate
#6
My understanding with Joe's was more MBC issues. I though EBC shouldn't matter where its pressure signal is from, within reason. As long as it has enough pressure to open the wastegate when its active. EBC should just maintain whatever you tell it to maintain for preassure. Maybe I missed something.
#7
not talking about any sort of boost controllers. yes ive seen the boost sag thread, but im always down for some pampering.
and not only on this forum, but elsewhere, ive seen it a million times, i just didnt know if there was any reason for the wastegate to read pressure at the housing rather than the manifold.
and not only on this forum, but elsewhere, ive seen it a million times, i just didnt know if there was any reason for the wastegate to read pressure at the housing rather than the manifold.
#10
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
Drawing from the manifold will kill the turbo if you run partial throttle in boost. The restriction of the throttle plate means you might be seeing 20-25psi in the pipes, but only 14psi in the manifold. You're liable to overspin the turbo and kill it.
If you're using an MBC, source it from the coldside IC pipes, as God intended.
If you're using an MBC, source it from the coldside IC pipes, as God intended.
#11
I've been toying with turbocharged cars for the past 13 years, and never once did I find any reason to run the wastegate reference line from the intake manifold. Wastegate diaphragms do not need to see vacuum, ever.
I've seen several people come up with torn wastegate diaphragms in years past, and almost all had something in common: They were using the intake manifold as their boost reference. Coincidence ? Sure, maybe. These wastegate diaphragms were not built to see vacuum, and one can only assume that exposing them to 20-24inHg for extended periods of time is a shitty idea and practice.
Now another reason (call me crazy if you must) to not use the manifold is the negative effect of having such a drastic change in pressure / vac operate the wastegate. Again, these were built to operate on boost pressure to open, and spring pressure to return the flapper to closed position. By using the intake manifold for a reference, you are pushing and pulling the rubber diaphragm very aggressively as opposed to just letting the spring return operate.
"If you're using an MBC, source it from the coldside IC pipes, as God intended." < Truth.
I've seen several people come up with torn wastegate diaphragms in years past, and almost all had something in common: They were using the intake manifold as their boost reference. Coincidence ? Sure, maybe. These wastegate diaphragms were not built to see vacuum, and one can only assume that exposing them to 20-24inHg for extended periods of time is a shitty idea and practice.
Now another reason (call me crazy if you must) to not use the manifold is the negative effect of having such a drastic change in pressure / vac operate the wastegate. Again, these were built to operate on boost pressure to open, and spring pressure to return the flapper to closed position. By using the intake manifold for a reference, you are pushing and pulling the rubber diaphragm very aggressively as opposed to just letting the spring return operate.
"If you're using an MBC, source it from the coldside IC pipes, as God intended." < Truth.
#12
Makes sense, though I had an iwg referenced from the mani for over 2 years on my 00 with no ill effect on wga.
The part throttle over-boost thing makes sense too, but I measured pressure from coldside, mani, and hotside before with no drastic swings from either place. I guess I didn't do part throttle boost long enough for it to build up? It was a large turbo too maybe that's why.
oh well.
Joes thread breaks down placement perfectly.
Do what it says.
The part throttle over-boost thing makes sense too, but I measured pressure from coldside, mani, and hotside before with no drastic swings from either place. I guess I didn't do part throttle boost long enough for it to build up? It was a large turbo too maybe that's why.
oh well.
Joes thread breaks down placement perfectly.
Do what it says.
#13
Totally. Like I said, I may have just experienced some coincidental failures, but it still struck me as odd. When something isn't designed to operate in a certain way, I have reservations about doing just that. I mean, ****, how many years have gone by where Garrett, Precision, Turbonetics, etc, all manufactured turbochargers that had a reference ports sticking out of the compressor housing ?
#14
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
If you have a half-decent intercooler, it doesn't matter - I've tuned Miatas that reference from the hotside on a 1bar spring make 14.6psi at the intake manifold. If your intercooler is garbage and drops 2-3psi, then you're going to want to source post-IC to get that boost back.
Similarly, if you have decent EBC, it doesn't matter. Our EFR kits will source from the hotside because 1. we have good intercoolers, 2. we have EBC, and 3. it's more elegant than a 1/4" wastegate source hose running through the entire engine bay.
Similarly, if you have decent EBC, it doesn't matter. Our EFR kits will source from the hotside because 1. we have good intercoolers, 2. we have EBC, and 3. it's more elegant than a 1/4" wastegate source hose running through the entire engine bay.
#15
yeah the difference between running in vac and boost seems to be the answer i stumbled across the most. still tons of good info guys i appreciate it. looks like ill be swapping out tonight...may be a PITA cuz for whatever reason my gsp charger didnt have a nipple for the line in the compressor housing. but ill make somethin work with the hot side pipes or something.
Thread
Thread Starter
Forum
Replies
Last Post