My first dyno
#1
Senior Member
Thread Starter
iTrader: (7)
Join Date: Jul 2006
Location: SLC UT
Posts: 1,126
Total Cats: 0
My first dyno
Disappointed
Supposedly this dyno reads super low.
All the modded speed3's were reading 210 to 220 hp uncorrected, mine read 148.4
Stock 1.6 roughly 60,000 miles
13PSI gt2560
2.5 catless exhaust
1/4 mile run
Here's a shot of the datalog.
They're cooling fans were worthless. The video shows the first pull. after that I went up to the front and held one of the blowers on the air intake while my friend held one in front of the intercooler.
All in all I'd say I need more tuning amongst other things.
Supposedly this dyno reads super low.
All the modded speed3's were reading 210 to 220 hp uncorrected, mine read 148.4
Stock 1.6 roughly 60,000 miles
13PSI gt2560
2.5 catless exhaust
1/4 mile run
Here's a shot of the datalog.
They're cooling fans were worthless. The video shows the first pull. after that I went up to the front and held one of the blowers on the air intake while my friend held one in front of the intercooler.
All in all I'd say I need more tuning amongst other things.
Last edited by nicacus; 10-16-2010 at 06:39 PM.
#4
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,039
Total Cats: 6,607
Your exhaust is fine. I managed to crack the 200 HP mark with my stock 1.6 on a Dynojet with a 2.5" exhaust, a plain ole' ceramic cat, and a tiny little Greddy TD04H-15G turbo running 13-14 PSI, but it took a fair amount of tweaking to get there. I picked up over 20 ft/lbs in the midrange with a few simple fuel adjustments.
I don't see AFR logged anywhere, either on the dyno sheets or on your image of the datalog.
Your ignition timing looks quite conservative to me as well. The base timing in the spark map isn't too bad, but take, for instance, the point where the cursor is (5515 RPM @ 171 kPa). The base map is calling for about 15° there, and yet you're only seeing 7.6° in the log. Part of that is probably MAT (133°F, climbing to 169°?!) although the curves (MAT vs. Spark) don't seem to be tracking the way I'd expect. Get in there and figure out what's pulling your spark advance.
I don't see AFR logged anywhere, either on the dyno sheets or on your image of the datalog.
Your ignition timing looks quite conservative to me as well. The base timing in the spark map isn't too bad, but take, for instance, the point where the cursor is (5515 RPM @ 171 kPa). The base map is calling for about 15° there, and yet you're only seeing 7.6° in the log. Part of that is probably MAT (133°F, climbing to 169°?!) although the curves (MAT vs. Spark) don't seem to be tracking the way I'd expect. Get in there and figure out what's pulling your spark advance.
#5
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,025
Total Cats: 304
Omg. How did I make 209 whp on a smaller turbo with a shitty setup? Oh..I know...I wasn't on a mustang dyno, and for 1/4 mile proof, I ran at a track that printed out a time slip saying 13.9.
A: you need to get on a real dyno.
2: you need to hit a real drag strip
D: you have to be making at least 200 whp. There is something wrong with your car/ tune.
A: you need to get on a real dyno.
2: you need to hit a real drag strip
D: you have to be making at least 200 whp. There is something wrong with your car/ tune.
#6
Omg. How did I make 209 whp on a smaller turbo with a shitty setup? Oh..I know...I wasn't on a mustang dyno, and for 1/4 mile proof, I ran at a track that printed out a time slip saying 13.9.
A: you need to get on a real dyno.
2: you need to hit a real drag strip
D: you have to be making at least 200 whp. There is something wrong with your car/ tune.
A: you need to get on a real dyno.
2: you need to hit a real drag strip
D: you have to be making at least 200 whp. There is something wrong with your car/ tune.
He has a 1.6L and you have a 99? lol either way the needs a tune badly.
#7
Senior Member
Thread Starter
iTrader: (7)
Join Date: Jul 2006
Location: SLC UT
Posts: 1,126
Total Cats: 0
Here's the tune I was running and the full log.
Here's a snapshot of the AFR target table
3" exhaust is in the works.
I wouldnt have gone to a mustang dyno normally, but this was a local mazda dyno day, so it was fairly cheap. Plus I figured it would show me where I was at after having the car turbo for 3+ years.
Here's a snapshot of the AFR target table
3" exhaust is in the works.
I wouldnt have gone to a mustang dyno normally, but this was a local mazda dyno day, so it was fairly cheap. Plus I figured it would show me where I was at after having the car turbo for 3+ years.
#10
Your ignition timing looks quite conservative to me as well. The base timing in the spark map isn't too bad, but take, for instance, the point where the cursor is (5515 RPM @ 171 kPa). The base map is calling for about 15° there, and yet you're only seeing 7.6° in the log. Part of that is probably MAT (133°F, climbing to 169°?!) although the curves (MAT vs. Spark) don't seem to be tracking the way I'd expect. Get in there and figure out what's pulling your spark advance.
#11
Senior Member
Thread Starter
iTrader: (7)
Join Date: Jul 2006
Location: SLC UT
Posts: 1,126
Total Cats: 0
So out of fear I switched it to the current map.
If there is a certain one anyone recommends i'm up for it
As for fuel all of the tuning there has been from the autotune in tunerstudios.
I'd love to hear suggestions on what to do there as well.
#16
Senior Member
Thread Starter
iTrader: (7)
Join Date: Jul 2006
Location: SLC UT
Posts: 1,126
Total Cats: 0
Ok, went for a canyon drive and did some logs with a new spark table.
this:
Didn't hear any knock, and got no hesitation with that table. Is that table too aggressive?
Notice the manifold air temps on this log compared to the dyno log.
Ambient temperature was around 59* F
Here's a GPS track of the datalog.
http://maps.google.com/maps/ms?msa=0...c5ba47c728cbe5
datalog attached
this:
Didn't hear any knock, and got no hesitation with that table. Is that table too aggressive?
Notice the manifold air temps on this log compared to the dyno log.
Ambient temperature was around 59* F
Here's a GPS track of the datalog.
http://maps.google.com/maps/ms?msa=0...c5ba47c728cbe5
datalog attached
Thread
Thread Starter
Forum
Replies
Last Post
Lincoln Logs
Dynos and timesheets
4
09-23-2015 12:26 PM