Braineack

iTrader: (62)

Thanks brah. 18psi whatcha got??

Braineack

iTrader: (62)

I put a vacuum pump on it, and it's all over the place; highly inconsistent.

sometimes it wont pull any vacuum, other times it would pull and hold nearly the max of the unit.

one time i started the car, pumped it a bit, turned it off and tried again and it literally wouldn't pull any vacuum at all. When it does pull vacuum it seems to hold it...but other times it was leaking off ever so slightly.

I feel like it should always pull the same amount of vacuum all the time right?

JasonC SBB

Does anyone know if the 99/00 ABS prop valve is the same as the 01-sport non-ABS prop valve?

rleete

iTrader: (21)

Sounds to me like the diaphram is loose aroung the perimeter. Sometimes it seals, but sometimes it doesn't.

18psi

iTrader: (76)

I don't think they're same. Brake feel on my 99 and 00 was nothing like brake feel on my 01. I say feel cause that's the only way I have "measured it", but the brakes on my 01 are WAY better

xcoldricex

iTrader: (3)

what was wrong with the brass fittings?

would the 929 1" master cylinder be a better upgrade than the sport MC? has anyone used that 929 master - do new lines need to be made?

Braineack

iTrader: (62)

i had two snap...once installing, one while driving.

chpmnsws6

iTrader: (12)

This better be fixed by now...

ScottFW

iTrader: (4)

I snapped one while installing. Had to be an issue with the threads or the taper of the flare just not mating well with the stock lines. It just didn't seal, so I tightened it a bit at a time, and it eventually snapped. I got a replacement and used some sealant on the threads and it's been okay for 2+ years, but it's in the back of my head as a weak point and I'm still going to get some of TSE's steel fittings.

xcoldricex

iTrader: (3)

anyone do the 929 master cylinder swap? i read around and saw that people were getting the ABS version, so that's what I did. problem is it has 2 ports instead of the 3 the stock miata has (has two for the front brake lines). can i just install a brass T to spllit the lines?

Braineack

iTrader: (62)

yeah youll have to in that case.

Orion ZyGarian

Man, threads like this make me want to start a Miata wiki/FAQ etc. thing that has ALL of the information you could ever want on the NA/NB in one spot. What fits between the two, and what factory upgrades are. People that are new to Miatas might not know that they can get 1.8 brakes for their 1.6, or even Sport NB brakes as an upgrade. I didnt know until this thread that the booster/master was different as well.

Braineack

iTrader: (62)

there is one already...and we try to put the good posts into the "useful saved posts" thread.

Orion ZyGarian

Yeah I love the useful saved posts ..where's the FAQ/wiki though? And I dont mean the Miata.net one, though its a good start

By the way, happy birthday you old fart

Braineack

iTrader: (62)

miataturbo.wikidot.com

Orion ZyGarian

Wow I never heard about this wtf...thanks man I should be spending more time on there now

xcoldricex

iTrader: (3)

trying to bleed some new wilwoods with a sport booster/929 mc swap. bench bled the MC, i can bleed the rears fine, no pressure gets built up when i go to bleed the fronts though. gravity bled the two top bleeders on both sides and fluid comes out ... but no pressure after pumping up the brakes - sounds like a bad MC? unfortunately you can't buy new 929 MC's anymore. it doesn't look like i'm having luck with this reman..

Orion ZyGarian

Depending on where you get it from, many parts places have lifetime warranties on them. I'm pretty sure I got a lifetime on my slave cylinder, because as you know, Miatas tear through them like butter through wet paper