DeerHunter

Towards the end of my MSM build thread, I recount how I had a catastrophic power steering failure on track. I've removed what I believe to be the offending leaking hose, part number NC10-32-688, pictured below:





Hose in question is coloured orange and it connects the pump to the reservoir




The trouble is, the part is no longer manufactured by Mazda and there is zero inventory in North America. I haven't had much success finding an aftermarket replacement either. Anyone know of a suitable alternative or perhaps have a spare off a wreck? My next track day is coming up and I'm dead in the water until I can get this figured out.

Thanks.

aidandj

iTrader: (5)

Mazda motorsports lets me get through checkout with one in the cart. Maybe they have some.

thirdgen

iTrader: (26)

I tore mine like a decade ago and just got a straight piece of hose and clamped it on. It works even with the kink, since 2007.


this would be cool to compression sleeve/ AN adapt to braided though...

ridethecliche

iTrader: (2)

You sure do love compression sleeves lol

eddyc49

I used this one for my repositioned reservoir, but it should work in the stock location if you cut one of the sides short.

it's a heater hose for a Acura Integra.

thirdgen

iTrader: (26)

^Amazing!!!

DeerHunter

Good idea - thanks. I'll look for one locally here and see what I can do with it. Any issues with a heater hose carrying ATF? I guess a rubber hose is a rubber hose and there shouldn't be anything to worry about.

DeerHunter

$11 at local distributor. Fingers crossed that it works out. Thanks again.

DeerHunter

Grrrr! Distributor recommended against the coolant hose as it's not rated for oil. Found a length of oil-rated 5/8" ID hose at a local hose supplier and hooked it up. After pressure-washing the engine bay to make everything clean, it turns out it wasn't the hose at all but the high-pressure fitting at the top of the pump. Even after tightening, it still sprays fluid out whenever the wheel is turned. Bad pump? Bad fitting? Would replacing the crush washer perhaps do the trick? I'm disheartened.

Leafy

iTrader: (1)

Hose #6 is the one that breaks. The hardline cracks. It's a pretty well known issue in auto-x cars.

DeerHunter

Is this the one you mean? (highlighted in red):

Leafy

iTrader: (1)

Yup.

DeerHunter

Great. Local dealer will have one in by tomorrow afternoon. I was also able to source a suction hose from Treasure Coast, so hopefully I'll have things back in a running state fairly soon. Thanks all.

Leafy

iTrader: (1)

If I was you I'd be working on a long term solution for that pressure line. It's going to break again.

DeerHunter

Any suggestions?

JamieH

I see you've already sourced the part, but for future reference, the NA hose should work on the NB. Mazda Part # NA02-32-684B

The NA hose is currently still available. And after a bit of trimming, it should fit the NB.

DeerHunter

Good to know - thanks. Hopefully I won't have to worry about that particular hose again.

Leafy

iTrader: (1)

Make one with an fittings. Iirc the one to the pump is hard to find, and I think I machined a custom one for someone while in college once.

DeerHunter

Sounds like an opportunity for the aftermarket. Hint, hint.

DeerHunter

New hard line went in today. Unlike most repairs, this was actually easier than anticipated. Drop the undertray and the bottom compression connector was within easy reach. Replacement hard line had all-new brackets and was a breeze to install.

I'm still not sure why the old one failed. The upper bracket locks the hard portion of the line completely in place. It cannot move relative to the engine, so engine torquing shouldn't be able to fatigue it. Puzzled...

Anyway, thanks to everyone who chimed in. I'm back in business for the next track day.