Cant connect to MS
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Aug 2008
Location: Evansville, Indiana
Posts: 314
Total Cats: 0
Cant connect to MS
So, my built MSII wont connect to my computer. i'm using the usb-->serial adapter recommended by DIY, and i downloaded the drivers off their site.
what else do i need to do?
what else do i need to do?
#5
Junior Member
Thread Starter
iTrader: (1)
Join Date: Aug 2008
Location: Evansville, Indiana
Posts: 314
Total Cats: 0
so i was able to connect to the MS after i used the correct baud rate. however, when it does connect i get an error message about "firmware signature mismatch".
i tried to follow the tunerstudio instructions on the turbomiata wiki, but when i hit the detect firmware button in the new project box, TS crashes everytime....
then i decided to just download the firmware, i assume it's one of these:
http://www.msextra.com/doc/ms2extra/files/alpha/
but which one?
halp?
i tried to follow the tunerstudio instructions on the turbomiata wiki, but when i hit the detect firmware button in the new project box, TS crashes everytime....
then i decided to just download the firmware, i assume it's one of these:
http://www.msextra.com/doc/ms2extra/files/alpha/
but which one?
halp?
#6
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Nobody can answer that for you, except maybe the guy who built the ECU, and that's only if he remembers. You're the guy looking at the screen, so this is going to fall on you. You have two options:
- ask the MegaSquirt what firmware has been loaded and then download the same definition from the internet and point your TunerStudio project to it
- Download a firmware definition of your choice, flash it to your MegaSquirt, and then point your TunerStudio project to it
#7
Junior Member
Thread Starter
iTrader: (1)
Join Date: Aug 2008
Location: Evansville, Indiana
Posts: 314
Total Cats: 0
Nobody can answer that for you, except maybe the guy who built the ECU, and that's only if he remembers. You're the guy looking at the screen, so this is going to fall on you. You have two options:
ask the MegaSquirt what firmware has been loaded and then download the same definition from the internet and point your TunerStudio project to it
ask the MegaSquirt what firmware has been loaded and then download the same definition from the internet and point your TunerStudio project to it
is that right?
i didnt see any on that list that looked right. if memory serves it was 2.1.1a
Download a firmware definition of your choice, flash it to your MegaSquirt, and then point your TunerStudio project to it
The application requires MS2/Extra firmware. I generally recommend 2.1.0 for MS2 noobs, unless you have a DIYPNP (go with the newest 3.0.3 for DIYPNP).
The application requires MS2/Extra firmware. I generally recommend 2.1.0 for MS2 noobs, unless you have a DIYPNP (go with the newest 3.0.3 for DIYPNP).
i apologize for being such a total worthless
#8
I had the same problem with mine till i updated the firmware to 3.03
you can get the batch file and stuff here to update it
http://msextra.com/doc/ms2extra/files/alpha/
you can get the batch file and stuff here to update it
http://msextra.com/doc/ms2extra/files/alpha/
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM