magnamx-5

iTrader: (7)

egaSquirt Download 1.04

Opened comm port 7 at 9600.
Reading signature:
Signature: "Bowling & Grippo v. 2.xxx or 3.000"

magnamx-5

iTrader: (7)

Right no jumper so wtf is this jumper. I don't think i can run dos on XP can I?

Braineack

iTrader: (62)

see on the board where it say BOOT. put a jumper there (any wire in both spots)

then try to upload your X_mod.s19 file that easy therm made with the downloader. make sure the ports are correct.

magnamx-5

iTrader: (7)

Do i have to solder the wire in? or can i lay it there or is that just plain silly?

cjernigan

iTrader: (13)

stick each end of the wire in the holes
use a paperclip if you have to

magnamx-5

iTrader: (7)

MegaSquirt Download 1.04

Reading C:\Program Files\EasyTherm\megasquirt_mod.s19:
Detected MS-I (HC908) code.
Entry point: 0x0000
Code range : 0x8128-0xfffe
File read successfully.

Opened comm port 7 at 9600.
Wake up attempted:
Wakeup successful.

Erasing:
Erased.

Writing:
Write complete, 326 records, 4934 bytes.

Verifying:
Signature:
Verify complete.
Elapsed time: 17.48 seconds

It worked an i just tryed to reflasht the easytherm agian this is what i got+ another non com situation on my Megatune. So it was the Downlaoder corrupting the file for sure. I relaoded my last MSQ and she started right up. I still don't know **** about what to move where but i am glad my **** is running agian anyway. Thanks guys and Scot or Chad lemme know if you are interested in modding my MS.

Braineack

iTrader: (62)

no.

let me send you the file to flash. that file is messed up that you are uploaded. should be 1700 records.

pm me your email.

magnamx-5

iTrader: (7)

Hmm well i don't trust myself to remove the resistor. but thanks for the files i will ask Nick if he can do it.

Braineack

iTrader: (62)

it's two snips with a cutting tool of some sorts. otherwise the temps will be about 20* low.

cjernigan

iTrader: (13)

Werd. Use a good sharp pair of dikes and cut each lead carefully. Easy stuff Rich.

magnamx-5

iTrader: (7)

oh so i dont need to suck up solder etc hmm i think i will do this after work. So by doing this i will no longer need to reflash easytherm, or i will need to do both. I am just making sure here. I modded the codebased outputs as well. Wow this is gonna be cool if it works. Did I mention you guys are the best

cjernigan

iTrader: (13)

Removing the resistor makes it so MS can read the sensor correctly, otherwise it will read 20* lower than it should. You will still need to reflash the MS with the .s19 file scott sent you and then put the 3 .ini files into Program Files->Megatune->mtCFG.
You have to do all of those steps to get it to work and read correctly in megatune.

Braineack

iTrader: (62)

then all you gotta do is move the resistor and wire on the back adn you can run spark.

firedog25

How long have you had epilepsy and how the hell do you take pictures while having a seizure?

reddroptop

iTrader: (4)

magnamx-5

iTrader: (7)

sorry old *** camera trying to make the best of my lighting and show as much detail as possible. seriusly the camera is from like 1999. Good ole fuji the only one that hasn't craped out on me yet.

magnamx-5

iTrader: (7)

Ok so to recapp. I move my IGN wire to the outside resistor, and then I cut a resistor. And this will make my easytherm and, spark work?

Braineack

iTrader: (62)

did you move the resistor as well like the above diagram?


that and your codebase changes should get spark to work.

magnamx-5

iTrader: (7)

No i have moved nothing yet. This is the guy who does not own a soldering iron remember, i have a propane torch i use on plumbing but i doubt that will do well on the MS baord. I see what you mean for the spark mod but I can seem to find the resistor i am suposed to eliminate for the temp mod. I just tryed to call 2 scoops of hoah he has more mad skilz in this area than i do but i got no response.

Braineack

iTrader: (62)

look at the front of your board.


there is a row of resistors. just above & of "Bowling & Grippo"

count up 5. there's a blue one. R7. rip it out.