Installed HR code
#1
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2008
Location: Central, TX / Bay area, CA
Posts: 1,260
Total Cats: 5
Installed HR code
So I installed HR and i still cant get my car to idle leaner than 12.6 or so with out it stumbling, I thought HR was supose to be able to fix this problem or was i worng? also my whole tune is wrong now i seem to have to change everything for it to run right, But i am not having any random miss fires or anything like that. I am running RX7 550's and a LC1 wide band, mbc, air meter delete, all ran great before high ress, anything im missing? Also in mega tune if i go into the configurer and try to change it to my defalt LC1 it wont let me select it. I am new to this MS thing so help me out.
#4
Its deff something you did wrong. I idle my 550's at 15.0 all day long. You will have to completely retune your fuel map. When I switched to Hi res my entire map was way lean.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#7
PM me your email address and I'll send you what I have.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#10
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2008
Location: Central, TX / Bay area, CA
Posts: 1,260
Total Cats: 5
Ok so i Reloaded the firmware and my msq, Still cant get it to run leaner than 13.6 or so with out surging. I dataloged and opened mega log viewer, Ran VE analizer accepted the table loaded it in and now everything is like 10:1 or richer. i did this at least 3 times and it did the same thing. Can anyone help me or atleast tell me how to reload the stock firmware so i can drive my car agian.
#12
Ok so i Reloaded the firmware and my msq, Still cant get it to run leaner than 13.6 or so with out surging. I dataloged and opened mega log viewer, Ran VE analizer accepted the table loaded it in and now everything is like 10:1 or richer. i did this at least 3 times and it did the same thing. Can anyone help me or atleast tell me how to reload the stock firmware so i can drive my car agian.
YOU MUST DISCONNECT THE IGNITOR WHEN YOU ARE RELOADING FIRMWARE, AND LEAVE IT DISCONNECTED UNTIL YOU HAVE LOADED YOUR MSPNP MSQ FILE.
LEAVING THE IGNITOR CONNECTED WILL USUALLY RESULT IN DAMAGE TO THE IGNITOR.
The ignitor connection is shown in this photo.
To download the firmware, go into the MegaSquirt folder and select the “MSPNP MM9093 with AFM” folder if you are using the stock AFM and sensors, or the “MSPNP MM9093 without AFM” folder if you have removed the AFM and installed a GM style IAT sensor. Power up the MSPNP, disconnect the ignitor plug shown above, and connect the MSPNP to your computer. Close any programs such as MegaTune that communicate with MegaSquirt. Run the file named “download-firmware.bat”. This will launch the downloading program.
The downloading program will first prompt you for your COM port, and then ask if you are using a boot jumper. The MSPNP already has MSnS-E firmware loaded, so when the program asks if you are upgrading from standard MegaSquirt code, press N. Once you press N, the download will begin. Do not turn off the MSPNP, plug in the ignitors, or close the downloading program until the download is complete. Normally you do not need to install a boot jumper or open the ECU to reload firmware.
Once the firmware download is complete, you MUST reload the base map, or your updated map which was based on the base map, before reconnecting your ignitor. The .msq file for the base map will be located in the same folder as the firmware update above. Load the base map .msq file using the File -> Open command in MegaTune, and then you can reconnect your ignitor.
LEAVING THE IGNITOR CONNECTED WILL USUALLY RESULT IN DAMAGE TO THE IGNITOR.
The ignitor connection is shown in this photo.
To download the firmware, go into the MegaSquirt folder and select the “MSPNP MM9093 with AFM” folder if you are using the stock AFM and sensors, or the “MSPNP MM9093 without AFM” folder if you have removed the AFM and installed a GM style IAT sensor. Power up the MSPNP, disconnect the ignitor plug shown above, and connect the MSPNP to your computer. Close any programs such as MegaTune that communicate with MegaSquirt. Run the file named “download-firmware.bat”. This will launch the downloading program.
The downloading program will first prompt you for your COM port, and then ask if you are using a boot jumper. The MSPNP already has MSnS-E firmware loaded, so when the program asks if you are upgrading from standard MegaSquirt code, press N. Once you press N, the download will begin. Do not turn off the MSPNP, plug in the ignitors, or close the downloading program until the download is complete. Normally you do not need to install a boot jumper or open the ECU to reload firmware.
Once the firmware download is complete, you MUST reload the base map, or your updated map which was based on the base map, before reconnecting your ignitor. The .msq file for the base map will be located in the same folder as the firmware update above. Load the base map .msq file using the File -> Open command in MegaTune, and then you can reconnect your ignitor.
I might be able to get some of the hi res issues corrected if you could post a copy of your MSQ and a data log, too.
#15
Senior Member
Thread Starter
iTrader: (5)
Join Date: Jan 2008
Location: Central, TX / Bay area, CA
Posts: 1,260
Total Cats: 5
Why do you say that the LC-1 is off? seems to be working fine now on LR. Im leaving on vacation and didnt want to screw things up agian so i will not be running the HR code untill i get back.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM