MegaSquirtSanta - Custom Modifications / Firmware
#64
One question I am not sure if it is much to ask but is it not posible to use another pin to as input to ac up signal. The reason i am using pe1 for table switch (is the only pin available for this) I already have pe0 for launch control so i can use the clutch lock out and i just need another pin to activated the code (js4(ad7),js5(ad6),Js11(pa0) are suitable) I prefer js4 or js5 this way if I ever need to go full cop I would not have any issue but js11 is acceptable to I am running waste spark right now any ways.
Thanks again
Juan
Thanks again
Juan
#65
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2011
Location: Australia
Posts: 178
Total Cats: 3
One question I am not sure if it is much to ask but is it not posible to use another pin to as input to ac up signal. The reason i am using pe1 for table switch (is the only pin available for this) I already have pe0 for launch control so i can use the clutch lock out and i just need another pin to activated the code (js4(ad7),js5(ad6),Js11(pa0) are suitable) I prefer js4 or js5 this way if I ever need to go full cop I would not have any issue but js11 is acceptable to I am running waste spark right now any ways.
Thanks again
Juan
Thanks again
Juan
If you can contribute a wiring guide for DIYPNP board for any of these switches I'll look at adding the code. I'm just not sure if you have enough Input circuits to condition the incoming switches, how to pull them out of the uS module etc, and I don't want to be left with support questions asking how to safely enable those inputs without your help.
G
#66
What uses these now? js4(ad7), js5(ad6), Js11(pa0) ??
If you can contribute a wiring guide for DIYPNP board for any of these switches I'll look at adding the code. I'm just not sure if you have enough Input circuits to condition the incoming switches, how to pull them out of the uS module etc, and I don't want to be left with support questions asking how to safely enable those inputs without your help.
G
If you can contribute a wiring guide for DIYPNP board for any of these switches I'll look at adding the code. I'm just not sure if you have enough Input circuits to condition the incoming switches, how to pull them out of the uS module etc, and I don't want to be left with support questions asking how to safely enable those inputs without your help.
G
#67
What uses these now? js4(ad7), js5(ad6), Js11(pa0) ??
If you can contribute a wiring guide for DIYPNP board for any of these switches I'll look at adding the code. I'm just not sure if you have enough Input circuits to condition the incoming switches, how to pull them out of the uS module etc, and I don't want to be left with support questions asking how to safely enable those inputs without your help.
G
If you can contribute a wiring guide for DIYPNP board for any of these switches I'll look at adding the code. I'm just not sure if you have enough Input circuits to condition the incoming switches, how to pull them out of the uS module etc, and I don't want to be left with support questions asking how to safely enable those inputs without your help.
G
http://www.diyautotune.com/diypnp/do...Launch_Control
Home work done Just follow the instructions for launch control input and in tunner studio pic the pin that was use in the pnp for the "lauch control mod" js4, js5 or pa0
Juan
#68
Also we you can build in the proto board the following circuit :
http://msextra.com/doc/ms1extra/MS_E....htm#mapswitch
Then is as simple as taking the output signals from this circuit and jumper them to the appropriate available pin in the pnp (ADC1=JS5, ADC2=JS4,PA0=JS11)
Juan
http://msextra.com/doc/ms1extra/MS_E....htm#mapswitch
Then is as simple as taking the output signals from this circuit and jumper them to the appropriate available pin in the pnp (ADC1=JS5, ADC2=JS4,PA0=JS11)
Juan
#69
Here you can find a more detailed list of what is the use of the already mentioned cpu pins
for both ms2 and he ms2 module that the pnp use.
http://msextra.com/doc/ms2extra/MS2-...htm#ms2options
for both ms2 and he ms2 module that the pnp use.
http://msextra.com/doc/ms2extra/MS2-...htm#ms2options
#70
Spent the morning adjusting the clutch switch to avoid accidentally getting into CL idle while lightly slipping the clutch (traffic crawling). I ended up having to fashion an extender to the pushrod of the switch, so that it will only be triggered by a deep clutch press (when actually shifting). Maybe I just have a heavy left foot, but this mod did the trick for me!
#71
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2011
Location: Australia
Posts: 178
Total Cats: 3
I'm sorry, and I'm not trying to be difficult, but after following those links, I can't easily see what I'd follow to duplicate your desired requirement of enabling another hardware input.
Have a look at this link.. http://www.diyautotune.com/diypnp/docs.html
And tell me which of the 18 pin center header inputs you think you want to add - I'd like to ensure I test this and validate that indeed the input is working.
G
Have a look at this link.. http://www.diyautotune.com/diypnp/docs.html
And tell me which of the 18 pin center header inputs you think you want to add - I'd like to ensure I test this and validate that indeed the input is working.
G
#72
I'm sorry, and I'm not trying to be difficult, but after following those links, I can't easily see what I'd follow to duplicate your desired requirement of enabling another hardware input.
Have a look at this link.. http://www.diyautotune.com/diypnp/docs.html
And tell me which of the 18 pin center header inputs you think you want to add - I'd like to ensure I test this and validate that indeed the input is working.
G
Have a look at this link.. http://www.diyautotune.com/diypnp/docs.html
And tell me which of the 18 pin center header inputs you think you want to add - I'd like to ensure I test this and validate that indeed the input is working.
G
#74
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jun 2011
Location: Australia
Posts: 178
Total Cats: 3
The ms2/extra team have changed the license agreement and have restricted the works.... So I may not legally be able to do anything beyond 3.1.4
I'd suggest you follow and chime in if you feel this is a good/bad thing.
G
I'd suggest you follow and chime in if you feel this is a good/bad thing.
G
#77
I read the licence agreement and i think you are taking this the wrong way. They only want you to show the the code before realeasing it they never wanted to stop development. That why the source code is available.
I think the dev already reply one of your post at msextra just show them the code before you release it and i am sure they won't deny you the permission for distribution. also if is for personal use yo can modify the code and you do not have to ask permission for that only for redistribution.
I think the dev already reply one of your post at msextra just show them the code before you release it and i am sure they won't deny you the permission for distribution. also if is for personal use yo can modify the code and you do not have to ask permission for that only for redistribution.
#78
I read the licence agreement and i think you are taking this the wrong way. They only want you to show the the code before realeasing it they never wanted to stop development. That why the source code is available.
I think the dev already reply one of your post at msextra just show them the code before you release it and i am sure they won't deny you the permission for distribution. also if is for personal use yo can modify the code and you do not have to ask permission for that only for redistribution.
I think the dev already reply one of your post at msextra just show them the code before you release it and i am sure they won't deny you the permission for distribution. also if is for personal use yo can modify the code and you do not have to ask permission for that only for redistribution.
you have to remember that they have a brand to protect, and crappy code releases can tarnish their reputation quickly.