MS3, MS3x, for a 2002. What to buy?
#21
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,504
Total Cats: 4,079
Parts will cost your $4 shipped at digikey.com
This picture shows in green what would normally go there, and in gray what I'm installing, right?
And for future parts, do I need any pieces that didn't come with the kit?
Here's an MS2 I did with that circuit so you can get an idea of all the mods you need to do (Take in mind there's a lot more circuits on that board than you'll need when using the MS3X card):
If he wanted to go MS3, all he would have to do is remove the ms2 daughter board and replace with the MS3 and flash the firmware. He could even load his MS2 MSQ and be on his way in like ten minutes.
#23
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
There is no need to do "Joe's Spark Circuit".
When you buy the MS3 kit and MS3x, they come with the DB37 connectors you need to make a harness. Talk to y8s about the mazda ECU connector, I think he has a spare.
The Input Circuit you DO need to add is this one outlined here: http://westfieldmx5.devocht.com/index.php?section=35
see Step 50.
You will also need to do the alternator control circuit outlined above.
Also very little needs actually be populated on the mainboard, so save yourself the trouble when building it and omit the circuits that are pointless. It should also be outlined on the build thread linked above.
Don't follow any other "additional/optional circuits" or the step 65.
When you buy the MS3 kit and MS3x, they come with the DB37 connectors you need to make a harness. Talk to y8s about the mazda ECU connector, I think he has a spare.
The Input Circuit you DO need to add is this one outlined here: http://westfieldmx5.devocht.com/index.php?section=35
see Step 50.
You will also need to do the alternator control circuit outlined above.
Also very little needs actually be populated on the mainboard, so save yourself the trouble when building it and omit the circuits that are pointless. It should also be outlined on the build thread linked above.
Don't follow any other "additional/optional circuits" or the step 65.
#24
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
Wow, I'm also intimidated by the alternator circuit. That seems like a lot of crap to fit in the proto area, not to mention I don't know how I'll fit 3 wires into those holes.
#27
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
Any idea where I can get an MS3 base map for an 02? I'm still working with the stim but I'm having trouble getting it to sync or show anything, but it doesn't have any kind of map I don't think.
#31
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
Well, I loaded that map, and I get 158 errors, the rpm shows 65043 and it still doesn't sync. I feel like such a noob, my MS1 worked perfectly the first time I plugged it in when I built that one.
#35
Elite Member
Thread Starter
iTrader: (3)
Join Date: Apr 2008
Location: Outside Portland Maine
Posts: 2,023
Total Cats: 19
jumpers and switches on the JimStim? I think so, but I guess I don't really know where they're supposed to be. I know the switches are right, and I know the O2 is set on narrow band, but besides that I don't know. the pin labelled "2nd trigger" is jumped to the pin labelled "I1A (25)"
The three-pin row labelled "Primary tach" has the left two jumpered, and the two right next to it appear to both be jumped to the 5V pull up. That looks like it for jumpers.
The three-pin row labelled "Primary tach" has the left two jumpered, and the two right next to it appear to both be jumped to the 5V pull up. That looks like it for jumpers.
#36
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,504
Total Cats: 4,079
you need to do this:
shouldn't need any pull up jumpers.
and also this:
2nd trigger jumper should stay where it is.
It'll never sync if the rpm shows 65043. You must first clear the conflict error.
shouldn't need any pull up jumpers.
and also this:
2nd trigger jumper should stay where it is.
It'll never sync if the rpm shows 65043. You must first clear the conflict error.