My MS2 Basemap - Miata Turbo Forum - Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


MEGAsquirt A place to collectively sort out this megasquirt gizmo

Reply
 
 
 
LinkBack Thread Tools
Old 12-28-2009, 10:57 AM   #1
Ben
Supporting Vendor
Thread Starter
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default My MS2 Basemap

For the folks that have been asking:

This is a MS2 3.0.3h with an incomplete dyno tune (trigger wheel started to break off the crank pulley while on dyno) plus a little cruise tuning on the road. It cold starts, cruises, and boosts well. Car is as listed in sig (stock engine 99, GT2560, 3" exhaust, 550cc injectors).

The dyno tune was not completed and spark is set pretty conservatively for GA 93 pump. I would consider this a solid basemap, however I am posting it "For Informational Purposes Only". Use this file, or any data from it, at your sole risk. My fuel pump was also running a bit weak, so it's likely that it will run rich on your car. Maybe. I dunno. Don't break your car by just copying this. If you blindly load this to your MS, you will break your car.

If you blindly load this to your MS, you will break your car. Be smart people.

After saying that, I know people will just load it to their car anyway. If you copy it, these things that are guaranteed to be incorrect for your car:
-My trigger wheel settings (vishnu 60-2 wheel)
-My ignition settings (LS2 coils)
-EGO (the VE table is set where I cruise at 14.7 everywhere, but I've been fooling with the EGO settings attempting to emulate inferior OEM performance to fool the stock computer)

https://www.miataturbo.net/forum/att..._autotune1.msq
Ben is offline   Reply With Quote
Old 01-31-2010, 08:31 PM   #2
Junior Member
 
Join Date: Mar 2007
Location: Chile
Posts: 95
Total Cats: 0
Default

where I can get this firmware?
macanha is offline   Reply With Quote
Old 01-31-2010, 08:39 PM   #3
Ben
Supporting Vendor
Thread Starter
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

Ben is offline   Reply With Quote
Old 01-31-2010, 08:48 PM   #4
Junior Member
 
Join Date: Mar 2007
Location: Chile
Posts: 95
Total Cats: 0
Default

thanks!
macanha is offline   Reply With Quote
Old 02-06-2010, 09:52 PM   #5
Senior Member
 
Join Date: Nov 2007
Location: Belgium
Posts: 939
Total Cats: 59
Default

if you use this msq with stock coils, make sure to change the spark output from inverted to normal.
WestfieldMX5 is offline   Reply With Quote
Old 02-07-2010, 11:46 AM   #6
Ben
Supporting Vendor
Thread Starter
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

Stock coils should also be going high/inverted with the DIYPNP, as well as a v3 or 3.57 with the standard spark circuits.
Ben is offline   Reply With Quote
Old 02-07-2010, 03:40 PM   #7
Senior Member
 
Join Date: Nov 2007
Location: Belgium
Posts: 939
Total Cats: 59
Default

I stand corrected. I thought the DIYPnP was the same as a standard V3 board where you choose not inverted (going low).
WestfieldMX5 is offline   Reply With Quote
Old 02-07-2010, 04:34 PM   #8
Boost Czar
iTrader: (61)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 72,892
Total Cats: 1,792
Default

Quote:
Originally Posted by Ben View Post
Stock coils should also be going high/inverted with the DIYPNP, as well as a v3 or 3.57 with the standard spark circuits.
with the v3.0 board, on ms2 , it still depends on how you build the spark output circuit, correct?
Braineack is offline   Reply With Quote
Old 02-07-2010, 04:41 PM   #9
Ben
Supporting Vendor
Thread Starter
iTrader: (33)
 
Ben's Avatar
 
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,689
Total Cats: 99
Default

Yes, it depends on which output you build. Just follow the procedure for the output you use.

Another reason why map sharing can be bad.
Ben is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Back to Stock Part Out!! Turbo Parts, MS2 Enhanced 01-05, Suspension, and MOAR! StratoBlue1109 Miata parts for sale/trade 16 10-02-2015 10:39 AM
mslabs MS2 - Idle control issue ndragun MEGAsquirt 0 09-20-2015 11:28 PM
Ms2e Not Syncing Dobzeh MEGAsquirt 2 09-10-2015 07:34 AM
emanage ultimate 1.6 basemap xmacmiatax ECUs and Tuning 0 09-08-2015 05:17 PM
Ms2e Not syncing Help? ConnorSzcz ECUs and Tuning 0 09-04-2015 03:46 PM


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 11:50 PM.