MEGAsquirt A place to collectively sort out this megasquirt gizmo
Sponsored by:
Sponsored by:

Please help with no idle issue

 
Old 02-25-2019, 08:40 PM
  #1  
Newb
Thread Starter
 
Join Date: Nov 2010
Posts: 2
Total Cats: 0
Default Please help with no idle issue

MS-1 Extra 029y4a
MIata 1.8 BP N/A stand alone
oem CAS and Ignitors
Locost 7 build
TechEdge 2y2

Engine starts right up and runs a few seconds then stalls. I can not get the engine to idle. I have spent 2 weeks researching this issue on line and have tried adjusting required fuel to lean and rich but doesn't make any difference. I don't know what to try or look at next and would appreciate a look at my msq if I have a setting incorrect. Also any suggestion on how to troubleshoot my problem.

I have no running history on the engine.
Just completed the WBO2 build and not sure it's working correctly.

Thanks -Ron
Attached Files
File Type: msq
log1.msq (47.1 KB, 11 views)
File Type: csv
log1.csv (82.4 KB, 9 views)
Rskovira is offline  
Old 02-28-2019, 11:05 PM
  #2  
Newb
 
Join Date: Oct 2017
Posts: 37
Total Cats: 0
Default

Could be something to do with the 0% duty cycle at idle at upper temp you have on your settings, although my firmware has entirely different options. Post current tune if you have anything else other than what you have provided.
SA58Junkie is offline  
Old 03-01-2019, 11:59 AM
  #3  
Newb
Thread Starter
 
Join Date: Nov 2010
Posts: 2
Total Cats: 0
Default

Thanks SA58Junkie for your time to respond. I did leave out important info as I am using a Ford 2 wire PWM IAC. Based on MS1Extra Software Manual the upper temp duty cycle can be set to 0 to start tuning. I think this closes the valve once upper temp is reached. I know the valve is open as I can put my finger on the intake and lots of air is pulled in a start up. If I manually restrict the intake of the IAC valve I get no difference in results. The engine still stalls after a few seconds so I haven't dealt with adjusting the parameters of this valve yet.

I have changed the req'd fuel value in steps from 13 to 2 and from 13 up 25 but don't see any effect on behavior, after a few seconds it stalls. It always starts up immediately but still stalls.

Is there a file different than the .msq that you are asking for? I thought the .msq file was the tune file????

I think I have a bad setting that is giving me this behavior since I have played with the fuel for last 3 weeks and same behavior. I'm wondering if my RPM looks right as it seems be jumpy on the .csv- The engine oscillates a little before it stalls but doesn't seem to like the chart. I am using the stock CAS with shielded cable grounded at the ECU end.
Rskovira is offline  
 
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
dale
MSPNP
8
01-04-2016 11:32 AM
sixshooter
Insert BS here
2
02-01-2013 06:26 PM
thirdgen
MEGAsquirt
21
03-11-2011 11:36 AM
poobs
MEGAsquirt
14
01-04-2010 02:12 PM
drftem
General Miata Chat
2
01-10-2007 01:55 PM


Thread Tools
Search this Thread
Quick Reply: Please help with no idle issue


Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.