Using TunerStudioMS for Tuning Megasquirt - Guide
#41
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,501
Total Cats: 4,080
save this somewhere and tell it use it: http://boostedmiata.com/MS/msq/firmware/msns-extra.ini
(right click, save link as, save as txt)
(right click, save link as, save as txt)
#44
AEM and AFR reading
Win7 Home Premium 64bit:
For my AFR Target tables to show up as AFR instead of volts using AEM I had to edit the mainController file in c:\users\Name\My Documents\TunerStudioProjects\Miata\projectCfg\mainController
Where Name is your username and Miata is whatever you called your project.
Changed these lines per instructions from the sticky thread
Look for the following lines in that "page = 7" section:
#elif AEM_LINEAR
afrBins1 = array, U08, 0, [8x8], "Volts", 0.0196, 0, 0.0, 5.0, 2
You want to make the following changes, which I've highlighted in red:
#elif AEM_LINEAR
afrBins1 = array, U08, 0, [8x8], "AFR", 0.038666, 255.0, 10.0, 20.0, 1
Also had to either adjust or disable User Account Control.
For my AFR Target tables to show up as AFR instead of volts using AEM I had to edit the mainController file in c:\users\Name\My Documents\TunerStudioProjects\Miata\projectCfg\mainController
Where Name is your username and Miata is whatever you called your project.
Changed these lines per instructions from the sticky thread
Look for the following lines in that "page = 7" section:
#elif AEM_LINEAR
afrBins1 = array, U08, 0, [8x8], "Volts", 0.0196, 0, 0.0, 5.0, 2
You want to make the following changes, which I've highlighted in red:
#elif AEM_LINEAR
afrBins1 = array, U08, 0, [8x8], "AFR", 0.038666, 255.0, 10.0, 20.0, 1
Also had to either adjust or disable User Account Control.
Last edited by Tremiata; 01-26-2010 at 07:53 PM. Reason: update
#45
Win7 Home Premium 64bit:
For my AFR Target tables to show up as AFR instead of volts using AEM I had to edit the mainController file in c:\users\Name\My Documents\TunerStudioProjects\Miata\projectCfg\mainController
Where Name is your username and Miata is whatever you called your project.
Also had to either adjust or disable User Account Control.
For my AFR Target tables to show up as AFR instead of volts using AEM I had to edit the mainController file in c:\users\Name\My Documents\TunerStudioProjects\Miata\projectCfg\mainController
Where Name is your username and Miata is whatever you called your project.
Also had to either adjust or disable User Account Control.
What do you mean by this?
#51
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,501
Total Cats: 4,080
Then under the configuration tab, change the ECU definition to "MS/Extra format hr_10 *******" If you dont have that, select other, then browse to the file you should have downloaded:
this one: http://boostedmiata.com/MS/msq/firmw...extra.ini.hr10
#52
Okay so I just started a new project and use that hr10 file as my firmare file. I activated it through MS and changed it to the AFR instead of volts. Now when I open my project it does not tell me about the differences. But, if I go in and just load my msq rather than loading the project first it says there is an error.
#57
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,501
Total Cats: 4,080
there should be a default or offlinetune .msq file that gets created for each project, so long as you open TS it'll preload the last tune you saved so you shouldnt be clicking on msq files, just open the software and itll already be loaded.
#59
It's under OPTIONS - PREFERENCES - PERFORM DIFFERENCE REPORT UPON CONNECT. Handy to have on if you like to hand-smooth and make changes in the comfort of your own home while offline or if you are constantly opening other peoples maps in your project.