OG Racing: PFC race pads.

Thread Tools
 
Search this Thread
 
Old 04-29-2015, 01:04 PM
  #41  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default

Originally Posted by aidandj
So without aero using the sport calipers over torques the rear brakes? So using the normal caliper with sport rotors is better for balance?
it all depends on your aero balance.

the debate over what calipers to use comes down to “it depends”. We are trying to find a dynamic balance under braking. A wide spread solution that many Miata’s are finding a good balance is with a aftermarket prop valve, a 11.75” Front brake kit (V8 roadsters for example), and the sport rotor Rear w/spacing out the factory 1.8 caliper. This combo has been found to provide good balance with most racers while keeping the parking brake. The sport caliper has a 1.375” piston and the 1.8 rear caliper has a 1.25” piston. The area of the pistons are 1.23^2” for the base and 1.48^2” for the sport caliper. A difference of 18.5% larger to the sport caliper. As there are only 3 ways to affect brake Tq on a given axle (hydraulic advantage, Pad compound, rotor Diameter) and changing piston size falls under hydraulic advantage. the change from 1.8 caliper to a sport caliper will net an increase in rear brake torque. Is this a good thing? If you had an trail braking happy rear end, no. This would make the problem worse. Adding a big rear wing should keep the rear in check and allow you to run more rear tq. Running a sport caliper is an option to add some extra Tq to the rear of the car, just take time to consider if you need the extra tq.

On my own set up my stats are as follows.
2400lbs, 450ish hp, afco shocks 550f/440r, 11.75" F, the 1.8l caliper/ sport rotor R. I can easily obtain a smooth trail braking condition. That might change as I intend to raise the wing 12” and add singular endplates. IMO if a parking brake wasn't needed I would rather have the V8roadsters 11.75” kit on all 4 corners. to bring balance is would choke down the prop valve. It makes bringing spars to the track that much easier and has considerably longer life.
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.

Last edited by OGRacing; 04-29-2015 at 04:06 PM.
OGRacing is offline  
Old 04-29-2015, 01:12 PM
  #42  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default

Originally Posted by turbofan
I was planning on the 97 compound per your recommendation in this thread. These are the tires I'm running: Federal Tyres - UHP - 595RS-R

My understanding is that they're supposed to be comparable to an RS3 or Rival in terms of grip, but I don't really know.

For running the regular 1.8 calipers on sport rotors there's some other adapter needed, no?

I'm not trying to clutter this thread, this is just regarded as the hot brake setup so it'd be good to know your recommended PFC setup. Curly recommended DTC 60s front and DTC 30s rear on these brakes.
I saw your email thank you for the inquiry.

We are currently backordered on the low tq option pads. Miata turbo has been eating them up. You can keep running the hawks as we wait for a new low tq pad to be sent. Or you can try the 11 compounds. The extra tq means you won’t be able to jam on the brakes as much as pro would. ( I jump the brakes like I’m kicking a football) you’ll need to take it easy but it wouldn't call it uncontrollable.

i street drive 01 compound pads. they start working at a very low temperature. so no need to worry about panic stops. it is a race pad so do take into consideration if you get caught in the rain. if you do wash the wheels as fast as you can. or follow my lead keep a set of black wheels for your track days. nobody notices if black wheels are dirty.

And please ask all the questions you can. I Try to help everyone I can. That’s what I’m here for. + It’s free bumps.
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.
OGRacing is offline  
Old 04-29-2015, 03:57 PM
  #43  
Supporting Vendor
iTrader: (3)
 
ThePass's Avatar
 
Join Date: Jul 2006
Location: San Diego
Posts: 3,303
Total Cats: 1,216
Default

Originally Posted by OGRacing
A difference of 18.5% larger to the sport caliper... the change from sport caliper to a 1.8 caliper will net an increase in rear brake torque.
First half of that correct, second half is backwards. Moving to 1.8 caliper from sport caliper is 18.5% reduction in torque.

-Ryan
__________________
Ryan Passey
ThePass is offline  
Old 04-29-2015, 04:05 PM
  #44  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default

Originally Posted by ThePass
First half of that correct, second half is backwards. Moving to 1.8 caliper from sport caliper is 18.5% reduction in torque.

-Ryan
DOHH fixing now
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.
OGRacing is offline  
Old 05-04-2015, 11:58 AM
  #45  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default






Congratulations to Ryan Passey #thepass.
On his win over the weekend running RTA unlimited class.

He was running pfc 01 compound.
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.

Last edited by OGRacing; 05-04-2015 at 02:08 PM.
OGRacing is offline  
Old 05-04-2015, 11:59 AM
  #46  
SADFab Destructive Testing Engineer
iTrader: (5)
 
aidandj's Avatar
 
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Default

**** son, winning GTA unlimited? Thats badass.
aidandj is offline  
Old 05-04-2015, 01:52 PM
  #47  
Junior Member
 
monkeywinky's Avatar
 
Join Date: May 2011
Posts: 66
Total Cats: 0
Default

RTA, you mean?
congrats to Ryan
monkeywinky is offline  
Old 05-04-2015, 02:08 PM
  #48  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default

woops
Originally Posted by monkeywinky
RTA, you mean?
congrats to Ryan
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.
OGRacing is offline  
Old 05-04-2015, 09:59 PM
  #49  
Supporting Vendor
iTrader: (3)
 
ThePass's Avatar
 
Join Date: Jul 2006
Location: San Diego
Posts: 3,303
Total Cats: 1,216
Default

Thanks Johnny!

For Saturday practice I co-drove the car with Sean. (Back-to-back sessions in 100* ambient heat all day long and the car didn't miss a beat, but that's a whole 'nother story). I've been telling him he HAS to try these PFC pads. I've been raving about them and he was skeptical. First session he comes back in and says these will be his next set of pads. Enough said

-Ryan
__________________
Ryan Passey
ThePass is offline  
Old 05-04-2015, 10:00 PM
  #50  
SADFab Destructive Testing Engineer
iTrader: (5)
 
aidandj's Avatar
 
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Default

Johnny, do I need to switch rotors when switching pads with these? Currently running stoptechs
aidandj is offline  
Old 05-05-2015, 07:28 AM
  #51  
Moderator
iTrader: (12)
 
sixshooter's Avatar
 
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,659
Total Cats: 3,011
Default

Originally Posted by aidandj
Johnny, do I need to switch rotors when switching pads with these? Currently running stoptechs
No. You shouldn't need to swap rotors for the sake of the pad compound. If they are worn and grooved you should be swapping them because of rotor wear, but other than that, no.
sixshooter is offline  
Old 05-05-2015, 08:12 AM
  #52  
SADFab Destructive Testing Engineer
iTrader: (5)
 
aidandj's Avatar
 
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Default

So I can go back and forth and have one set for track and one for street?
aidandj is offline  
Old 05-05-2015, 08:27 AM
  #53  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default

Originally Posted by sixshooter
No. You shouldn't need to swap rotors for the sake of the pad compound. If they are worn and grooved you should be swapping them because of rotor wear, but other than that, no.
i couldn't say it any better.

yep, you can swap them without worries.
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.
OGRacing is offline  
Old 05-07-2015, 11:08 PM
  #54  
Junior Member
 
vintagerust's Avatar
 
Join Date: May 2010
Location: Tampa, FL
Posts: 102
Total Cats: 2
Default

Just to clarify the whole sport rear caliper thing.

The bracket, or carrier, you use, is what determines whether you use a sport pad, or a standard 1.8 pad. If you want to use the standard 1.8 pads, you'll need to buy something like this: Miata Sport rear rotor Kit , so as to use the standard 1.8 carrier (bracket) on the larger sport rotors.

I currently use the sport caliper on the standard rotor and standard pads (along with the standard front brakes), because I wanted more rear brake bias. I found that the car was very prone to locking up in the wet under hard braking (not good in emergency stops), and I didn't want to wreck sliding through a red light, because I got caught on a yellow.
After back to back testing, the fronts still lock up before the rears, I stop in a shorter distance in the dry, and much shorter in the wet, without fear of locking up easily.

Mind you, I daily drive this car on parts store ceramic pads. Were I to be on stickier tires and upgrade to more aggressive pad compounds, that bias may change, but everyone's setup/driving style is a little different, and requires different needs.
I just wanted to mention the above.
vintagerust is offline  
Old 05-07-2015, 11:11 PM
  #55  
SADFab Destructive Testing Engineer
iTrader: (5)
 
aidandj's Avatar
 
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Default

Wut. This **** is getting confusing. So Sport Bracket with rear standard caliper will need sport pads?
aidandj is offline  
Old 05-08-2015, 03:08 AM
  #56  
Junior Member
 
vintagerust's Avatar
 
Join Date: May 2010
Location: Tampa, FL
Posts: 102
Total Cats: 2
Default

For the most part, yes.

Whether you can modify the standard pads to fit, I don't know. You may run into issues with the hardware. But from everything I've read when I was looking into swapping parts, the carriers determine which pads you use.
vintagerust is offline  
Old 05-08-2015, 01:30 PM
  #57  
Former Vendor
iTrader: (1)
 
Lincoln Logs's Avatar
 
Join Date: May 2010
Location: San Diego
Posts: 530
Total Cats: 64
Default

Not going to lie, I totally thought these were snake oil pads when Ryan first talked about them. After running back to back sessions in his car and experiencing how much win they are...I'm a believer. I can't see myself running anything else now...they are super smooth and control on application and release. At this point the PFC pads are hands down the best pads I've tried.
Lincoln Logs is offline  
Old 05-11-2015, 10:05 AM
  #58  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default

All,
We (OG Racing) managed to snag the last PFC 0636.97 pads that will be made. we only have 3 in stock. It will be some time until we have another low TQ option for the rear of 1.8l miatas, as we wait for PFC to replace the 97 compound with the 14 compound.




97 Compound.
Low Tq option. Best for low traction events. Example Dirt, rally cross, or low Grip tires. Very easy modulation, good flat Torque curve threw-out heat range. 10% less Tq then PFC 11 compound. suggested for the following tires. toyo R1R, Bridgestone RE-11A, Dunlpo star specs, Falken 615.

if you want to have one of the last 3 97 compounds you will need to email me. Johnny@ogracing.com.
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.
OGRacing is offline  
Old 06-01-2015, 04:29 PM
  #59  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default

monday... ughh no updates just bumping.
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.
OGRacing is offline  
Old 06-08-2015, 09:21 AM
  #60  
Supporting Vendor
Thread Starter
iTrader: (1)
 
OGRacing's Avatar
 
Join Date: May 2014
Posts: 1,797
Total Cats: 33
Default

Got more updates. NASA SE June Jam @Road Atlanta - Took home the nasa TTU (unlimited class) win on Sunday. Saturday i came in 2nd. i was running the PFC 01 compound on 11.75" pfc rotors, rear where sport good win racing "Sport rotors" with PFC 06 compound.









__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
Originally Posted by Mobius
Hopefully so, but let's hope it's never necessary. Experiencing your safety gear in action is ... not optimal.
OGRacing is offline  


Quick Reply: OG Racing: PFC race pads.



All times are GMT -4. The time now is 07:30 AM.