Bipes Installation Question. - Miata Turbo Forum - Boost cars, acquire cats.

Welcome to Miataturbo.net   Members
 


Prefabbed Turbo Kits A place to discuss prefabricated turbo kits on the market
Sponsored by:
Sponsored by:

Reply
 
 
 
LinkBack Thread Tools
Old 06-12-2007, 12:11 PM   #1
I'm Miserable!
Thread Starter
iTrader: (-1)
 
Join Date: May 2007
Location: West Sacramento Ca
Posts: 948
Total Cats: 0
Default Bipes Installation Question.

http://www.frontiernet.net/~bipesauto/BipesACU/

Am I reading this correctly, The cas wire (which is white) needs to be cut in half then put in two different places, and afm wire (which is red) needs to be tee'd off to the bipes?
Also, air temp sensor, where is that located? Or do I just Tee that from the ecu to the bipes?
I mean....Am I reading this right guys, Do I locate all these wires from the ecu and Tee the two off and cut the cas in half and put in two different spots?
Slidin'Miata916 is offline   Reply With Quote
Old 06-12-2007, 12:20 PM   #2
Boost Czar
iTrader: (61)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 72,813
Total Cats: 1,780
Default

everything you need is at the ECU.

everything but the CAS wire will be as simple as tapping into the wire...so either using vampire clips (not recommened), or carefully peeling back the coating of the wire you need, wrapping yours around that exposed wire and soldering it, then cover with shrink-wrap or electrical tape.

for the CAS you need to actually break the connection, so the wire goes in the Bipes and back out. Not just tapping off the wire for a signal.

Braineack is offline   Reply With Quote
Old 06-12-2007, 07:22 PM   #3
I'm Miserable!
Thread Starter
iTrader: (-1)
 
Join Date: May 2007
Location: West Sacramento Ca
Posts: 948
Total Cats: 0
Default

Thanks brain. Do these settings look ok? http://www.frontiernet.net/~bipesaut...20Page%203.htm

open
1.6L

6 Degree retard
1 degree retard for each 30 degrees F (15 degrees C)

2500 start retard
3800 full retard
Slidin'Miata916 is offline   Reply With Quote
Old 06-12-2007, 08:27 PM   #4
I'm Miserable!
Thread Starter
iTrader: (-1)
 
Join Date: May 2007
Location: West Sacramento Ca
Posts: 948
Total Cats: 0
Default

Can someone tell me what the timing should be on the cas itself?
Slidin'Miata916 is offline   Reply With Quote
Old 06-12-2007, 10:16 PM   #5
Boost Czar
iTrader: (61)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 72,813
Total Cats: 1,780
Default

at idle you should be at 10* (with 10 and gnd jumped)
Braineack is offline   Reply With Quote
Old 06-12-2007, 11:44 PM   #6
Cpt. Slow
iTrader: (25)
 
curly's Avatar
 
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 12,105
Total Cats: 518
Default

it doesn't need to be there does it? I left mine where I had it before the turbo, at 12. I just pulled approx. 2 more degrees then I thought I needed.
curly is offline   Reply With Quote
Old 06-13-2007, 12:33 AM   #7
Boost Czar
iTrader: (61)
 
Braineack's Avatar
 
Join Date: May 2005
Location: Chantilly, VA
Posts: 72,813
Total Cats: 1,780
Default

thats fine
Braineack is offline   Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Buzzing from driver side of engine bay? (MS3 install) nick470 MEGAsquirt 7 06-16-2017 02:53 PM
OTS Bilstein to motorsports ASN conversion stoves Suspension, Brakes, Drivetrain 5 04-21-2016 04:00 PM
Back to Stock Part Out!! Turbo Parts, MS2 Enhanced 01-05, Suspension, and MOAR! StratoBlue1109 Miata parts for sale/trade 16 10-02-2015 10:39 AM
Walbro 255lph Fuel Pump $50 lsc224 Miata parts for sale/trade 2 10-01-2015 10:17 AM
Low oil pressure after 1.8 swap and new turbo setup JesseTheNoob DIY Turbo Discussion 15 09-30-2015 03:44 PM


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -4. The time now is 09:42 AM.