Need help getting fuel with a power card
#1
Need help getting fuel with a power card
Hey guys, just bought a 96 miata with a jackson racing m45 on it. I guess its the gen 3 eaton because the front spacer from the nose to the housing is 1 inch thick.
Anyways, I have the stock pulleys on the kit. I put a new bypass valve on the car, and ordered a bypass check valve. Im looking to get a little more out of the kit. I was thinking about going to a bigger nose pulley, but am scared i'll run lean. Can I just get a vortech FMU (8:1), and run it along with the powercard? Will the power card be able to calculate the duty cycles quick enough with an FMU attached?
For reference I am only looking at running a nose pulley that is 65.5mm, which should be a total ratio of 1.99:1 for the pulley set ups.
Anyways, I have the stock pulleys on the kit. I put a new bypass valve on the car, and ordered a bypass check valve. Im looking to get a little more out of the kit. I was thinking about going to a bigger nose pulley, but am scared i'll run lean. Can I just get a vortech FMU (8:1), and run it along with the powercard? Will the power card be able to calculate the duty cycles quick enough with an FMU attached?
For reference I am only looking at running a nose pulley that is 65.5mm, which should be a total ratio of 1.99:1 for the pulley set ups.
#17
What kind of gains do people usually see going to the mega squirt (or any other stand alone). I started looking into the DIY pnp mega squirt. As far as the electronics go, it seems really easy. I am just a little on edge about tuning it.
Can someone who has maybe been on the edge about this, maybe help convince me...
The plan so far, or what I acquired cheap on craigslist.
1. 190LPH fuel pump
2. 315 supra injectors
3. mazda speed miata inter-cooler
4. 62.5mm pulley
The other option is to just go with the fuel pump, intercooler, pull timing, and run the power card.
Can someone who has maybe been on the edge about this, maybe help convince me...
The plan so far, or what I acquired cheap on craigslist.
1. 190LPH fuel pump
2. 315 supra injectors
3. mazda speed miata inter-cooler
4. 62.5mm pulley
The other option is to just go with the fuel pump, intercooler, pull timing, and run the power card.
#18
No one is going to convince you. If the numerous threads and posts on here from people switching and being happy are not convincing enough you just never will be convinced.
That said, I personally tuned a few setups that switched from band aids to full EMS and the results were good. No record breaking power gains, but torque and smoothness was picked up just about everywhere. More control and precision means the car will be more enjoyable and efficient if tuned correctly.
That said, I personally tuned a few setups that switched from band aids to full EMS and the results were good. No record breaking power gains, but torque and smoothness was picked up just about everywhere. More control and precision means the car will be more enjoyable and efficient if tuned correctly.
#20
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,660
Total Cats: 3,011
Get used rx7 460cc injectors for $50 and you can copy my fuel map for starters. It is nice to have a little headroom. The autotune feature of TunerStudio tunes your MegaSquirt fuel map for you so you don't have to be adept at anything. It really is so easy that I could do it.
The Mazdaspeed intercooler is so small that it isn't worth it. You need three of them to almost make a cheap chinese ebay intercooler.
Before you jump off and buy a MSPNP, though, I would seriously consider the MS3 Basic being custom built by Reverent. SO NICE! Especially for the money. I'll look for the link on this forum.
Edit: here it is https://www.miataturbo.net/ms-labs-m...ms-labs-69930/
Reverent will install and ship it with a base map to match the size of your injectors of choice.
The Mazdaspeed intercooler is so small that it isn't worth it. You need three of them to almost make a cheap chinese ebay intercooler.
Before you jump off and buy a MSPNP, though, I would seriously consider the MS3 Basic being custom built by Reverent. SO NICE! Especially for the money. I'll look for the link on this forum.
Edit: here it is https://www.miataturbo.net/ms-labs-m...ms-labs-69930/
Reverent will install and ship it with a base map to match the size of your injectors of choice.