aidandj

iTrader: (5)

Any part numbers on the seals

jpreston

iTrader: (4)

Nope. Sorry brah.

EO2K

iTrader: (37)

@jpreston, where did you pick up the Moog? Amazon? RockAuto? FLAPS? I'm wondering about the price compars with the Timken.

Thanks for posting up about it, it's always good to have more sources and comparisons for these types of things

jpreston

iTrader: (4)

Autozone online with a 20% off coupon for orders over $100. It's normally $98.99. Add a $4.99 duralast 3/8 drive 10mm socket (can't ever have too many) to the order and get the Moog for $80 shipped.

Autozone and Advance Auto both carry it, so you can pretty much always get it for at least 15% off.

turbofan

iTrader: (1)

Does the Moog box say made in Japan, and CarQuest say China?

jpreston

iTrader: (4)

Yep. I didn't notice that. Weird, since the bearing is stamped Japan. The Timken box doesn't say, but it had to have been made on the same line as the carquest. I can't find anything at all to differentiate those two.

hornetball

iTrader: (4)

I just installed a couple of the Mazdaspeed HD "blueprinted" fronts after going through Mazda OEMs like water. Will report on how they stand up to Red.

scenturion

iTrader: (9)

What torque did you use? I installed a set and after they heat up one or both hum fairly noticeably at highway speeds. I called MMD yesterday and they said to re-torque them to 160-180ftlb, whereas the manual says 130-150ftlb iirc.
I already hammered the caps in and put a detent into the locknut, so it will be annoying to undo all of that.

hornetball

iTrader: (4)

Thanks for the heads-up on that. I used the maintenance manual number.

EO2K

iTrader: (37)

@hornetball, did you repack the OEM ones or just run them as they came out of the box?

hornetball

iTrader: (4)

I just ran them as-is. I recently purchased some of the good grease and will venture into Aidansworld once I kill off these Mazdaspeed HDs (these are supposedly already repacked with the good stuff).

aidandj

iTrader: (5)

Could you measure the OD of the machined part where the ABS ring would go?

jpreston

iTrader: (4)

I can tonight. I see what you're getting at... it looks like the diameter might be correct to allow you to install the tone ring onto a non-ABS hub, but it looks to me like the depth of the cut is too shallow.

aidandj

iTrader: (5)

The tone rings aren't big. I've seen other places that people say the non abs hubs still have a place for the ring.

Midtenn

iTrader: (15)

Later OEM hubs had machining for tone rings on all hubs. We just press the tone rings off damaged hubs and put them on good ones all the time.

scenturion

iTrader: (9)

The seal on my OEM NB1 front hub reads
"NACHI" "F28BVV10" "JAPAN"

edit: this appears to be the part number for the entire hub assembly

EO2K

iTrader: (37)

For everyone still subbed or following this thread, please go here and read: https://www.miataturbo.net/race-prep...el-hubs-90331/

You have been warned.

GasJunkie

I am in the middle of repacking new Timken 513155 wheel hubs and hit a bit of a snag.

The Timken bearing has a different arrangement on the inner race. There is a "retaining channel" that grabs a series of 4 tabs on the retainer.



When I drive out the inner race with the crack washer method, it breaks off two of the retaining tabs on the race. (Red and Green arrows in photo) Just to be sure, I did both hubs and had the same result.



I'm planning to repack and reassemble as I don't think these tabs do much other than ease assembly at the factory. Anybody differ?

EO2K

iTrader: (37)

Is the 513155 for a Miata application? Or alternate part number?

That sucks, but prop for good pics. Te mo data, te bettah.

jpreston

iTrader: (4)

Agreed. I wouldn't worry about it if the tabs are cleanly broken off. The Raybestos hub I recently disassembled had 8-12 small tabs for the same purpose. A few of them broke when I hammered out the race, but most of them were still hanging on and flopping around loosely, like they would eventually fall off inside the hub. That one left me nervous. Yours looks like nothing to worry about.

513155 is the Timken Miata ABS hub part number. 513152 is non-ABS.