Is this right? (Pic)
01-14-2014, 10:02 PM
#5
Junior Member
Thread Starter
Join Date: Feb 2012
Location: Atlanta, Ga
Posts: 280
Total Cats: 36
More I think about it more pissed I am. Not visible in add pics and not in the description. It took me a second to see the hole... no way the seller didn't see it. Also not described were the repairs to the header but they seem to be well done. I'm requesting a refund.
Reply
0
0
01-14-2014, 10:44 PM
#7
I just received your email about this. Honestly I never even saw that. I never installed this kit. I opened the box when I got it and put it away in the garage. I have since decided to go bigger so I sold the kit. I am very sorry about this. I am just as surprised and pissed about this as well being I bought this from a member on here too. Who never said anything about it either.
Have you pressurized it at all to see what happens?
This is who I bought it from biohzrd53188. https://www.miataturbo.net/miata-par...rything-74728/
Have you pressurized it at all to see what happens?
This is who I bought it from biohzrd53188. https://www.miataturbo.net/miata-par...rything-74728/
Last edited by Evergreen; 01-15-2014 at 12:34 AM.
Reply
0
0
01-14-2014, 11:53 PM
#9
Originally Posted by 18psi
Nope. But,
That hole goes to the oil drain bolt and not the passages. take out the bolt and see for yourself. I think its a casting defect from garrett, and not damage, to damage the chra like that you'd leave a huge mark. The guy I got it from used it for a couple years if not more, with no problems.
Also the manifold was repaired by the guy I got it from. Very good fabricator and it was a hairline crack that appeared on the runner and downpipe after about 2-3 years of use. he repaired it properly and didn't cut any corners. He disclosed the repair to me and I disclosed it to the guy that got it from me, obviously he didn't disclose it to the next guy, and likewise with the next guy after that. Then it was sold to you, probably undisclosed too.
Tubular manifolds crack. Its not a matter of if, its a matter of when. Even high quality ones from absurdflow and artech.
Hope that helps.
That hole goes to the oil drain bolt and not the passages. take out the bolt and see for yourself. I think its a casting defect from garrett, and not damage, to damage the chra like that you'd leave a huge mark. The guy I got it from used it for a couple years if not more, with no problems.
Also the manifold was repaired by the guy I got it from. Very good fabricator and it was a hairline crack that appeared on the runner and downpipe after about 2-3 years of use. he repaired it properly and didn't cut any corners. He disclosed the repair to me and I disclosed it to the guy that got it from me, obviously he didn't disclose it to the next guy, and likewise with the next guy after that. Then it was sold to you, probably undisclosed too.
Tubular manifolds crack. Its not a matter of if, its a matter of when. Even high quality ones from absurdflow and artech.
Hope that helps.
Reply
0
0
01-16-2014, 09:50 PM
#11
Elite Member
Join Date: Oct 2013
Location: Cedar City, UT
Posts: 2,764
Total Cats: 951
Totally normal on the 2860. Mine has the exact same hole in it. It is a void that is opened when they drilled tapped a bolt hole. Does not go INTO the turbo housing or oil/coolant area at all.
Don't worry about it, I freaked out about it until I studied it closer and saw that it has no relation to the internals of the turbo.
Don't worry about it, I freaked out about it until I studied it closer and saw that it has no relation to the internals of the turbo.
Reply
0
0
02-03-2014, 08:17 AM
#13
Junior Member
Thread Starter
Join Date: Feb 2012
Location: Atlanta, Ga
Posts: 280
Total Cats: 36
Yes, 3 reasons. I had someone look at the turbo who knows way more that I. He was not overly concerned with the casting/ tapping void/ error, and basically stated what others above have said- it should not be an issue. However, he also said that the shaft has way too much play in/out- that it should have almost none. This one moves roughly 2mm and needs to be rebuilt.
So...
1. Undisclosed casting error.
2. Undisclosed manifold repairs.
3. Undisclosed rebuild required.
It's a train wreck. Why not just allow me to return it? I have not used it and I'm not a satisfied buyer. Shouldn't have to involve Paypal IMHO. I also offered to keep the system if Evergreen paid for the rebuild by refunding $500.
Do I want to go spend double and buy an FM no electronics kit? No. Also been trudging along buying things assuming this would work- things like the IC kit, an external WG, etc.
So...
1. Undisclosed casting error.
2. Undisclosed manifold repairs.
3. Undisclosed rebuild required.
It's a train wreck. Why not just allow me to return it? I have not used it and I'm not a satisfied buyer. Shouldn't have to involve Paypal IMHO. I also offered to keep the system if Evergreen paid for the rebuild by refunding $500.
Do I want to go spend double and buy an FM no electronics kit? No. Also been trudging along buying things assuming this would work- things like the IC kit, an external WG, etc.
Reply
0
0
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
