MS3X testing with Jim Stim - No RPM Signal
#1
Junior Member
Thread Starter
iTrader: (2)
Join Date: Jan 2013
Location: Michigan
Posts: 207
Total Cats: 5
MS3X testing with Jim Stim - No RPM Signal
Hi, newbie here, happy to have built me MS3X, now into the testing phase. Good news - TPS, MAT, O2, CLT all work nicely, however I don't seem to be able to get RPM
I have
1. Confirmed using led test I can get RPM on the JimStim
2. On the JimStim - Jumpered Primary Tach for VR signal, Jumpered 5V to Pullup on 2 and P, set dipswitch on for 2,3,6.
3. On the TS ignition control - setup spark mode = miata 99-05
Not sure what to try next, any help/ideas welcomed. Thanks very much
I have
1. Confirmed using led test I can get RPM on the JimStim
2. On the JimStim - Jumpered Primary Tach for VR signal, Jumpered 5V to Pullup on 2 and P, set dipswitch on for 2,3,6.
3. On the TS ignition control - setup spark mode = miata 99-05
Not sure what to try next, any help/ideas welcomed. Thanks very much
#7
Junior Member
Thread Starter
iTrader: (2)
Join Date: Jan 2013
Location: Michigan
Posts: 207
Total Cats: 5
OK, hooked up the 2nd trigger to Pin 32, still nothing. I made a few logs files I can see MAP and TPS moving as I turned them up and down in the time history. Still not RPM, not sure what line item to look at for crank and cam...
#10
Junior Member
Thread Starter
iTrader: (2)
Join Date: Jan 2013
Location: Michigan
Posts: 207
Total Cats: 5
I just found the composite logger - sorry missed this...Anyway i tried to save a file but the file was empty, in the left column it says empty read no data received from the controller
#11
Junior Member
Thread Starter
iTrader: (2)
Join Date: Jan 2013
Location: Michigan
Posts: 207
Total Cats: 5
Some progress....
Found my JP7 jumper was not in place (I forgot the Cam is a Hall and the crank is a VR !) and after tweaking pot R11 I got a signal...Yay !
CL file attached.
I still dont see a RPM signal on the main tach, but I think this is progress in the right direction now....
Found my JP7 jumper was not in place (I forgot the Cam is a Hall and the crank is a VR !) and after tweaking pot R11 I got a signal...Yay !
CL file attached.
I still dont see a RPM signal on the main tach, but I think this is progress in the right direction now....
#12
Junior Member
Thread Starter
iTrader: (2)
Join Date: Jan 2013
Location: Michigan
Posts: 207
Total Cats: 5
OK ! Got it ! Looks like I was running my primary tach at 5v not 12v, Tuner studio is now synced and I have RPM's to play with ! Thanks for your help Braineack ! It took some trial and error but with the tip about the composite log that really helped !
Is there anything like a check list for things to test once you have RPM's ? I feel like I'm ready to test some things out with the Jimstim but not sure where to begin...
I'm also looking for a Fuel and spark table for a NA 1.8 with VVT, if anybody has anything close to get me started/running....
Thanks again !
Is there anything like a check list for things to test once you have RPM's ? I feel like I'm ready to test some things out with the Jimstim but not sure where to begin...
I'm also looking for a Fuel and spark table for a NA 1.8 with VVT, if anybody has anything close to get me started/running....
Thanks again !
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM