BUT HATER IS RACECAR?!

He built a race car for his race car so he can race while he race

duhh

Wait til you see my next WEIRD TRICK after this car is done.

install a turbo backwards because 100kpa is entirely too much boost for your car?

Backwards turbo = negative boost? Becausestreetcar? :robert:

Direct exhaust injection.

http://forums.pelicanparts.com/uploa...1194654061.jpg

LIES!

Ok ok, fine. MY 15x10s don't.

Which... i swear i will get measurements today. Been trying to clean the car before i tear it apart in the garage. Fenders and doors are absolutely destroyed from the brake issues. Don't think it's salvageable. Passenger front wheel also trashed from brake issue. Feels bad.

Don't act like you don't love mexiflush

I have my stock nb1 injectors if youre on the prowl.

I am. I'm looking for as close to free as possible. A guy on another forum has a set, but hasn't come back to me with price yet. If you get in quick at $Free.99 +small flat rate, i'll "buy" from you probably.

Did you get this pump? I like the fact that the sock looks like an equivalent to the stock sock, which, if it is, makes this kit a bargain.

I bought the DW100, with some piece of crap sock and then had to shell out a high percentage of the original expenditure to get a stock sock (as the big boys say it's the only one to have).

So, did you get it and did the sock look like a stock sock?

Side note: you can have my NB1 injectors. I will ship them to you for $10 total price.

I didn't get it yet. I think Boileralum has a stock pump laying around that we might slam into the car to see if it works. And if it does, i may very well go ahead and buy the Amazon one anyways. This is a super nice car that we're planning on keeping for a very long time, so i don't mind "baselining" it to a greater extent than i normally would, otherwise.

I would love those injectors. :) PM incoming!

I still have the factory rear spoiler I took off mine if your new car doesn't have one and you feel the need.

The 1.125" Racing Beat sway bar is the one you want and what most of the guys on the mazda-speed forum (RIP) preferred despite the fact that the 1.25" was recommended.
I originally had the 1.25" bar and switched to the 1.125" bar after recommendations from other users.
It's surprising how much extra room becomes available with the slightly smaller bar - VERY important when it comes to intercooler plumbing routing (cold side in particular).
Also, you'll need the Racing Beat Bolts&Braces kit or chunky sway bar mount brackets with these bars (especially the 1.25" bar) because they'll tear the OEM brackets right off:
https://cimg1.ibsrv.net/gimg/www.mia...3ae41513ce.jpg
Note: This is NOT a Racing Beat sway bar but is a great photo of what will happen to the OEM bracket with a stiffer sway bar.

Crosslink: https://www.miataturbo.net/suspensio...-mounts-64406/

The RB blocks are a bit of a PITA since you have to take them out if you're trying to use the long bolt method to swap suspension. That said, that PITA is preferable to the PITA in the picture above...

I'm running the 1.125 bar with the blocks.

Ben, did you buy @thirdgen car, or just his engine? Trying to consolidate his "finally figured it out" thread and this one, in my head.

Thirdgen still has his miata. He just sold all the guts. I got the turbo setup. I think philly miata may have bought one of the shortblocks? I'm not sure.

I didn't know concealer had bought anything.

I'll never sell my car, still has the original bp in it...k20 is on a stand and I have a box of parts. What's up...

I had the dumb and I apologize for bringing you into this. Ben said he has Twodoor's old car and I mixed up names. Also, you are now in Mississippi now, right? He was saying he was going to MS to pick something up.

I'm kind of hesitant to post this, in case I'm still mixed up. But I can only learn.

EDIT: Nope that's Twodoor in MS.

No response needed.