Yet Another Gun Thread
#5761
I bet that's your culprit... that shiz has very low QA tolerances... primers could be way out of spec or seated too deep or some other shiz. Their batch-to-batch tolerances can be pretty bad.
I have a lower receiver with an RRA LPK sporting an ALG QMS trigger... would not light Russian steel ammo with JP low-power springs, and failed to fire every 10th or so with the factory springs. All my brass factory ammo and my reloads were fail-free. Try that box of Tula in another gun and see what happens.
I have a lower receiver with an RRA LPK sporting an ALG QMS trigger... would not light Russian steel ammo with JP low-power springs, and failed to fire every 10th or so with the factory springs. All my brass factory ammo and my reloads were fail-free. Try that box of Tula in another gun and see what happens.
#5762
"military ammo" will have harder primers to prevent guns with floating firing pins from accidentally lighting off the round in the chamber when dropped just wrong or dropped from a slingshot on a round without a mag in or any other silly scenarios. Tula and the other russian arsenal ammos are made like military ammo.
#5763
The hard primer is to prevent the momentum of the firing pin from setting off the round when the bolt goes forward. Unchamber a round from an AR-15 and you'll often be able to see an indentation in the primer from the firing pin continuing forward after the bolt has stopped moving.
Incidentally, I finally decided to stop acting like a poor and bought this: I was sold when I saw an installation video on youtube. I think it's a really clever system. It's a Troy Alpha 13" btw. To be honest, it wasn't even that expensive. Dunno why I waited so long.
Incidentally, I finally decided to stop acting like a poor and bought this: I was sold when I saw an installation video on youtube. I think it's a really clever system. It's a Troy Alpha 13" btw. To be honest, it wasn't even that expensive. Dunno why I waited so long.
#5765
It's a little silly right now. PSA has been selling a Freedom rifle kit (minus lower) for the past few months for $350 on their Daily Deals. Today's ad has 6.8spc full-auto BCG's for $60. And their non-blem Magpul lower is $150. I think the prices across the board at PSA have come down 10%-15% since the election, which is good, because they'd gone up at least that much in the preceding year feeding off the Hillary threat.
I keep saying the the prices on things must have bottomed out, and then I see 16" Anderson barrels for $65 and Ruger AR15's for under $500.
I also keep forgetting about Ebay for things... can you believe people still list things for actual auction? I'd been looking for an enhanced PSA stock for a couple months to finish off one of my Aero lowers, and I bid on one for $4 and won... +$6shipping, but still, $10 shipped and PSA wants $30.
PSA Classic Enhanced M4 Stock - Black - 77932641
Still, there are those people who don't want to "build" their own, and don't mind buying used... and don't mind that they don't have to go through a background check. I require a DL and CCW permit for all my face-to-face sales, and I only sell to guys with strong history/feedback on whatever local forum I'm advertising. I recently sold a gun that I'd had for three months back to the guy I bought it from.
I've also recently found extended take-down pins on sale for $5... that kind of shizzle is going on all my builds.
Extended Takedown & Pivot Pin w/ Detents & Spring 223 556 | eBay
I keep saying the the prices on things must have bottomed out, and then I see 16" Anderson barrels for $65 and Ruger AR15's for under $500.
I also keep forgetting about Ebay for things... can you believe people still list things for actual auction? I'd been looking for an enhanced PSA stock for a couple months to finish off one of my Aero lowers, and I bid on one for $4 and won... +$6shipping, but still, $10 shipped and PSA wants $30.
PSA Classic Enhanced M4 Stock - Black - 77932641
Still, there are those people who don't want to "build" their own, and don't mind buying used... and don't mind that they don't have to go through a background check. I require a DL and CCW permit for all my face-to-face sales, and I only sell to guys with strong history/feedback on whatever local forum I'm advertising. I recently sold a gun that I'd had for three months back to the guy I bought it from.
I've also recently found extended take-down pins on sale for $5... that kind of shizzle is going on all my builds.
Extended Takedown & Pivot Pin w/ Detents & Spring 223 556 | eBay
#5766
So I installed the free float tube and I highly recommend the Troy Alpha. A million times less of a hassle than Yankee Hill. Once the stock barrel nut is aligned with the gas tube, you just slide on the foreend and tighten three screws. It has a little tab to align everything. It was the easiest thing in the world. The only miserable part was tapping out the two pins retaining the front sight on the barrel. Shot the gun today and it turns out the gun is way more accurate free floated, go figure. When cold it shoots nice tiny groups, which is pretty impressive for PMC x-tac (a decent bulk mil spec round but nothing match quality).
I'm pretty happy with this gun now. Besides my suppressed guns, it's pretty much all I shoot anymore.
Just for yucks I decided to shoot the gun standing up with no bench rest or support of any kind for a while. I realized that it's been years since I shot a gun this way and my arm muscles aren't up to the task anymore. Just holding the gun steady takes a lot of effort and although it appears steady without magnification, at 4x, the reticle is just bobbing and swaying all over the place. Just keeping it on paper takes effort, let alone drilling a bullseye.
I'm pretty happy with this gun now. Besides my suppressed guns, it's pretty much all I shoot anymore.
Just for yucks I decided to shoot the gun standing up with no bench rest or support of any kind for a while. I realized that it's been years since I shot a gun this way and my arm muscles aren't up to the task anymore. Just holding the gun steady takes a lot of effort and although it appears steady without magnification, at 4x, the reticle is just bobbing and swaying all over the place. Just keeping it on paper takes effort, let alone drilling a bullseye.
#5767
This deal popped in my mailer just now... I'm not sure if this is a late April Fools joke or what.
Aero Precision lower for $90.
http://www.primaryarms.com/aero-precision-stripped-ar-15-lower-receiver-gen-2-apar501101
Or... Aero Precision Lower with "Free" LPK and Buffer Tube for $165.
Shopping
That's not even cool, man... customers don't forget **** like this. Besides, here locally, there area quite a few places selling Aero's for $60 cash... and I haven't seen an Aero online for more than $80 since the election. PA wants $90 plus shipping, and then fees... ****, I can get a complete lower locally for that much.
EDIT: Disregard my **** talking... this is for an AMBI lower, which they do have listed for $165... which Aero Precision also has for $165 on their website.
Aero Precision lower for $90.
http://www.primaryarms.com/aero-precision-stripped-ar-15-lower-receiver-gen-2-apar501101
Or... Aero Precision Lower with "Free" LPK and Buffer Tube for $165.
Shopping
That's not even cool, man... customers don't forget **** like this. Besides, here locally, there area quite a few places selling Aero's for $60 cash... and I haven't seen an Aero online for more than $80 since the election. PA wants $90 plus shipping, and then fees... ****, I can get a complete lower locally for that much.
EDIT: Disregard my **** talking... this is for an AMBI lower, which they do have listed for $165... which Aero Precision also has for $165 on their website.
#5769
Is it actually reliable, that's the question. There's nothing worse in 3 gun than a gun that fails. For the $600 of that gun you could get a used 1100 and put an extended bolt release/feed assist, extra big safety, and a feed tube on it. And the 1100 is basically guaranteed to shoot without being cleaned for 1k rounds without a failure of any kind.
#5775
I'll assume .308 in a 16" or 18" barrel... in that case, you're really beyond ethical kill range for hogs or deer. A 150grSP is down to 1000ftlbs or less and 50" of drop at 500yds. Of course there are plenty of guys out there who swear .243 is a great moose round.
The prices on everything are way down right now... PSA is selling their PA10's for like $700. I sold my AERO M5 last summer since my 6.8spc is solid up to 300yds, which is plenty for any white-tail hunting that I do.
I also saw that Classic has Sub2k's for $419 right now... VERY tempted, except a couple of my pharmaceuticals haven't panned out lately and all my play money is tied up! Stupid reverse split penny stocks... should have known better.
That .338 is a Savage BA110?
My next short-action semi-auto is going to be a .338 Federal. I think the caliber is primed to finally take off and all it will take is a couple more manufacturers to start selling it to see a revival. The NRA really needs to unfuck itself with National Reciprocity and get the HPA passed instead. A .338Fed in a 10" barrel with a 6" pinned suppressor would be the short-action version of the .300blk.
The prices on everything are way down right now... PSA is selling their PA10's for like $700. I sold my AERO M5 last summer since my 6.8spc is solid up to 300yds, which is plenty for any white-tail hunting that I do.
I also saw that Classic has Sub2k's for $419 right now... VERY tempted, except a couple of my pharmaceuticals haven't panned out lately and all my play money is tied up! Stupid reverse split penny stocks... should have known better.
That .338 is a Savage BA110?
My next short-action semi-auto is going to be a .338 Federal. I think the caliber is primed to finally take off and all it will take is a couple more manufacturers to start selling it to see a revival. The NRA really needs to unfuck itself with National Reciprocity and get the HPA passed instead. A .338Fed in a 10" barrel with a 6" pinned suppressor would be the short-action version of the .300blk.
#5776
That's the deal I picked up, $712 shipped. I'm sure they'll get a little cheaper on black Friday, but **** hunting in the cold.
I'd steer clear of the Sub2k. I picked up a stupid cheap 2nd gen last year, the one with the "improved" ergonomics...that thing needs another $200 thrown into it just to be useable. $650 gets you a really decent AR pistol, if you're going for the truck gun thing
I'd steer clear of the Sub2k. I picked up a stupid cheap 2nd gen last year, the one with the "improved" ergonomics...that thing needs another $200 thrown into it just to be useable. $650 gets you a really decent AR pistol, if you're going for the truck gun thing
#5779
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,441
Total Cats: 1,899
SilencerCo Releases First-Ever 50-State-Legal Suppressed Muzzleloader - Soldier Systems Daily
As a shooter of muzzleloaders, my brain is full of ****. No ******* way I would want to clean this thing.
SilencerCo Releases First-Ever 50-State-Legal Suppressed Muzzleloader
WEST VALLEY CITY, UT – September 19, 2017 – For the first time since the National Firearms Act (NFA) was created in 1934, civilians can enjoy suppressed shooting in all 50 states with SilencerCo’s latest innovation: the integrally suppressed Maxim 50 muzzleloader. In addition, this product can be purchased right now on the web with no regulation (no 4473, no tax stamp, no photographs or fingerprints) at store.silencerco.com and be shipped immediately to the purchaser with few exceptions*.
Residents in the 42 states that allow civilian ownership of silencers have to pay a $200 tax, fill out forms, send in photos, submit to fingerprinting, and wait months for the Bureau of Alcohol, Tobacco, Firearms, and Explosives (BATFE) and the Federal Bureau of Investigation (FBI) to review their forms and check their backgrounds—just to acquire an inherently-harmless product. With all the hoops to jump through, it’s no surprise that many Americans have difficulty committing the time or money it takes to save their hearing. Citizens may have had their Second Amendment rights suppressed, but innovation cannot be silenced.
With the invention of the Maxim 50, SilencerCo has created a product that is 100% legal for civilian ownership in all 50 states while providing hearing-saving suppression at a reasonable price point. How is this possible? By paying very close attention to the law.
The BATFE defines a silencer as a “device for silencing, muffling, or diminishing the report of a portable firearm . . .” By that definition, a silencer is only a silencer if it can attach to a firearm. The Maxim 50 is built on the base of a Traditions™ Vortek Strikerfire Muzzleloader. For those who know muzzleloaders, you’ll also know that they are not considered firearms by the BATFE but are instead antique firearms, a definition and difference that is very distinct. Because of this, a moderator that is permanently affixed to a muzzleloader is not legally defined as a silencer, since it does not attach to a firearm. With this realization, the Maxim 50 was born.
“It took a lot of creativity to arrive at this solution,” said Josh Waldron, SilencerCo CEO and Co-Founder. “We have been working on this product for three years, with most of that time spent waiting on a determination from the Technology Branch of the BATFE as to how this product would be classified. As soon as we received official word that it wouldn’t be considered or regulated as a silencer, we got to work on bringing the Maxim 50 to customers across the country.”
SilencerCo expects the Maxim 50 to be a hit not only with the NFA-loving crowd, but also with hobbyists and hunters. In many states, muzzleloader hunting begins days (sometimes weeks) before standard rifle season, giving hunters using this platform an edge. But this edge does come with caveats – antique firearms are usually loud, have lots of recoil, and the shooter has to battle the thick cloud of black powder smoke billowing from the barrel as they try to see if their shot connected with their game. The Maxim 50 solves all of the issues experienced by muzzleloader shooters while also drastically reducing the resulting smoke by more than two-thirds, allowing hunters to see the location of their shot and track their game.
SilencerCo is honored to finally be able to bring suppressed shooting to its customers across the country, especially in states such as California, Illinois, and New York, where civilian ownership of silencers is not currently allowed.
To see more on the Maxim 50 visit silencerco.com/maxim50.
WEST VALLEY CITY, UT – September 19, 2017 – For the first time since the National Firearms Act (NFA) was created in 1934, civilians can enjoy suppressed shooting in all 50 states with SilencerCo’s latest innovation: the integrally suppressed Maxim 50 muzzleloader. In addition, this product can be purchased right now on the web with no regulation (no 4473, no tax stamp, no photographs or fingerprints) at store.silencerco.com and be shipped immediately to the purchaser with few exceptions*.
Residents in the 42 states that allow civilian ownership of silencers have to pay a $200 tax, fill out forms, send in photos, submit to fingerprinting, and wait months for the Bureau of Alcohol, Tobacco, Firearms, and Explosives (BATFE) and the Federal Bureau of Investigation (FBI) to review their forms and check their backgrounds—just to acquire an inherently-harmless product. With all the hoops to jump through, it’s no surprise that many Americans have difficulty committing the time or money it takes to save their hearing. Citizens may have had their Second Amendment rights suppressed, but innovation cannot be silenced.
With the invention of the Maxim 50, SilencerCo has created a product that is 100% legal for civilian ownership in all 50 states while providing hearing-saving suppression at a reasonable price point. How is this possible? By paying very close attention to the law.
The BATFE defines a silencer as a “device for silencing, muffling, or diminishing the report of a portable firearm . . .” By that definition, a silencer is only a silencer if it can attach to a firearm. The Maxim 50 is built on the base of a Traditions™ Vortek Strikerfire Muzzleloader. For those who know muzzleloaders, you’ll also know that they are not considered firearms by the BATFE but are instead antique firearms, a definition and difference that is very distinct. Because of this, a moderator that is permanently affixed to a muzzleloader is not legally defined as a silencer, since it does not attach to a firearm. With this realization, the Maxim 50 was born.
“It took a lot of creativity to arrive at this solution,” said Josh Waldron, SilencerCo CEO and Co-Founder. “We have been working on this product for three years, with most of that time spent waiting on a determination from the Technology Branch of the BATFE as to how this product would be classified. As soon as we received official word that it wouldn’t be considered or regulated as a silencer, we got to work on bringing the Maxim 50 to customers across the country.”
SilencerCo expects the Maxim 50 to be a hit not only with the NFA-loving crowd, but also with hobbyists and hunters. In many states, muzzleloader hunting begins days (sometimes weeks) before standard rifle season, giving hunters using this platform an edge. But this edge does come with caveats – antique firearms are usually loud, have lots of recoil, and the shooter has to battle the thick cloud of black powder smoke billowing from the barrel as they try to see if their shot connected with their game. The Maxim 50 solves all of the issues experienced by muzzleloader shooters while also drastically reducing the resulting smoke by more than two-thirds, allowing hunters to see the location of their shot and track their game.
SilencerCo is honored to finally be able to bring suppressed shooting to its customers across the country, especially in states such as California, Illinois, and New York, where civilian ownership of silencers is not currently allowed.
To see more on the Maxim 50 visit silencerco.com/maxim50.