DIYs Plug and Play MEGAsquirt
#81
Supporting Vendor
iTrader: (5)
Join Date: Jun 2006
Location: Duluth, GA 30097
Posts: 803
Total Cats: 0
The NA didn't have a flux capacitor-- they were still working out the licensing at that point from the movie studios. I guess that's what makes it harder to find on the NA....
__________________
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
#83
Let's see if I've got this right?
1: Remove my Bipes, AFPR, Walbro, and 02Clamp.
2: Drop in some 440's.
3: Get an IAT and ditch the AFM.
4: Install LC-1.
5: Plug it in and start it.
6: Set the timing.
7: Go for a drive? Ok, Ok, go directly to the dyno nice and slow.
And all for $700!
WOW!!!
Is anybody going to the NE dyno-day going to have one? I know a few are MS'd, but anybody with the PnP?
1: Remove my Bipes, AFPR, Walbro, and 02Clamp.
2: Drop in some 440's.
3: Get an IAT and ditch the AFM.
4: Install LC-1.
5: Plug it in and start it.
6: Set the timing.
7: Go for a drive? Ok, Ok, go directly to the dyno nice and slow.
And all for $700!
WOW!!!
Is anybody going to the NE dyno-day going to have one? I know a few are MS'd, but anybody with the PnP?
#86
Deleting the AFM left a bit of a rich spike when running a map for with the AFM installed, so we have dialed in a second map for running without the AFM. We also have firmware already EasyThermed for the GM sensor as well as the Miata IAT sensor. The MSPNP comes with a CD that includes the base maps for both as well as the firmware and a copy of MegaTune.
#88
The Tuning Manual has already been done.
http://www.msextra.com/manuals/MS_Ex...nual_Index.htm
You should probably have a read of it otherwise you could melt your engine.
http://www.msextra.com/manuals/MS_Ex...nual_Index.htm
You should probably have a read of it otherwise you could melt your engine.
#89
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
Deleting the AFM left a bit of a rich spike when running a map for with the AFM installed, so we have dialed in a second map for running without the AFM. We also have firmware already EasyThermed for the GM sensor as well as the Miata IAT sensor. The MSPNP comes with a CD that includes the base maps for both as well as the firmware and a copy of MegaTune.
#92
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
The maps are going to be different, but there is enough knowledge base here that you'll at least get it started, and can tune the fuel yourself.
#94
Supporting Vendor
iTrader: (5)
Join Date: Jun 2006
Location: Duluth, GA 30097
Posts: 803
Total Cats: 0
We'll have a base map, firmware, and MegaTune config pre-setup for with AFM and without. The firmware is different due to the different IAT sensor calibration, same with the MegaTune setup. The base map is slightly different, mainly in the fuel table.
__________________
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
#95
Supporting Vendor
iTrader: (5)
Join Date: Jun 2006
Location: Duluth, GA 30097
Posts: 803
Total Cats: 0
Just got back in town and PM'd you, we'll see what we can work out....
__________________
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
Jerry a.k.a. 'FoundSoul'
DIYAutoTune.com
'91 Miata BEGi S3 GT2560 w/ MSPNP - 14.1psi - 253whp, 232wtq
'95 Miata n/a
A few other cars....
#96
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Thank you Jerry! It sounds like your vacation was well deserved.
BTW guys, I spoke with Jerry a few minutes ago. He informed me that he believes that their mapdaddy 4 bar w/ barometric MAP sensor should integrate well into the MSPNP inplace of the standard 2.5 bar. The difference in price is nominal; IMO well worth it. He is going to mock up a test board in a car sometime in the next day or three to make sure everything is kosher.
Ben
<edit>
Just ordered the knock sensor so
BTW guys, I spoke with Jerry a few minutes ago. He informed me that he believes that their mapdaddy 4 bar w/ barometric MAP sensor should integrate well into the MSPNP inplace of the standard 2.5 bar. The difference in price is nominal; IMO well worth it. He is going to mock up a test board in a car sometime in the next day or three to make sure everything is kosher.
Ben
<edit>
Just ordered the knock sensor so
__________________
91 Turbo | 10AE Turbo | 01 Track Rat | #323 Mazda Champcar
Chief of Floor Sweeping, DIYAutoTune.com & AMP EFI
Crew Chief, Car Owner & Least Valuable Driver, HongNorrthRacing
Last edited by Ben; 05-07-2007 at 12:40 PM.
#99
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
$700 - $720 for the MS plus ~$30 for an intake temp sensor and its bung
I'm also electing to get the baro correction 4 bar map sensor (standard is 2.5 bar and no baro correction) for an additional $60 plus knocksense for $98. So $900 total.
I'm also electing to get the baro correction 4 bar map sensor (standard is 2.5 bar and no baro correction) for an additional $60 plus knocksense for $98. So $900 total.