MS build thread
#81
Can someone go over my log file and see what I should, I get her started but shes running around 300rpms off beat like my lawn mower.
Crank trigger wheel settings were incorrect. changed them to the ones mentioned on the diyautotune page of installing MS in a miata. I'm getting there.
Appericate any help.
Justin
Crank trigger wheel settings were incorrect. changed them to the ones mentioned on the diyautotune page of installing MS in a miata. I'm getting there.
Appericate any help.
Justin
#85
Hi all, ok I got my timing dialed in at 300rpms where it shows 10 degrees at the crank and 10 btdc on megatune. though my afr's show around low 12.x rnage, so I know there is probably too much gas being injected but I can't seem to lean it out. Anyone have a clue? Uploaded my MSQ, let me know if you find anything strange, I'll upload a datalog in a minute as well
#87
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,046
Total Cats: 6,607
It's time to start working on your idle settings. They're way out of whack. You can stick with Warmup-based for now (eventually you'll want to go closed loop) but for starters, here's what your idle parameters look like:
Bump CrankingDC up to about 40. Also, you have the upper and lower idle duties backwards. As a baseline, set "Idle duty at lower temp" to 25, and "Idle duty at lower temp" to maybe 20. The way these work is that when the temp is below 129°, it uses the "lower" value, above 180° the upper, and interpolates between. You'll need to do some tweaking I'm sure, but this will get you idling. Then you can start doing coarse VE table correction to get your AFRs roughed in.
#88
I did the alterations to the idle settings, and still the same, running around 300rpms
Just a quick background info the engine was swapped into this car, runs fine on stock ecu, fine as the idle with the pervious tb was like 750rpms and sometimes it would dog down alot and come back up, well I took my former engines TB and clean it out and threw it on with a new gasket. Now it won't die down under 750rpms, but it idles high sometimes, 1000 rpms or around 800 rpms.
I thought it was the IAC was bad, but I poped off the IAC connector while my car was running on stock ecu and the idle jump from 750 to 1000rpms, so I think its working fine.
I'm gonna read though the MSextra manuals, I was able to get past all my other problems, I will get this installed and working!
I got my timing set where when it reads 10 degrees its at 10 degrees on the crank. So thats dialed in.
The stock ecu works fine, runs fine.
Joe I appericate the info though. If it still thinks its cranking does that mean it not using fuel\spark VE map info? So I need to fix the idle
Just a quick background info the engine was swapped into this car, runs fine on stock ecu, fine as the idle with the pervious tb was like 750rpms and sometimes it would dog down alot and come back up, well I took my former engines TB and clean it out and threw it on with a new gasket. Now it won't die down under 750rpms, but it idles high sometimes, 1000 rpms or around 800 rpms.
I thought it was the IAC was bad, but I poped off the IAC connector while my car was running on stock ecu and the idle jump from 750 to 1000rpms, so I think its working fine.
I'm gonna read though the MSextra manuals, I was able to get past all my other problems, I will get this installed and working!
I got my timing set where when it reads 10 degrees its at 10 degrees on the crank. So thats dialed in.
The stock ecu works fine, runs fine.
Joe I appericate the info though. If it still thinks its cranking does that mean it not using fuel\spark VE map info? So I need to fix the idle
#90
do you know if I can alter where it thinks cranking threshold is at off hand, I'm gonna check around.
I'm done fidiling for today, will try some tomorrow, time to bone up on my MSextra info.
Just for info I tried adjusting the idle screw with no effect to the 250-300rpm crank idle.
EDIT found cranking rpm, will change and test tomorrow.
Anyone with a 1.6l running MS show me what their cranking rpm is set at?
Thanks
I'm done fidiling for today, will try some tomorrow, time to bone up on my MSextra info.
Just for info I tried adjusting the idle screw with no effect to the 250-300rpm crank idle.
EDIT found cranking rpm, will change and test tomorrow.
Anyone with a 1.6l running MS show me what their cranking rpm is set at?
Thanks
#92
alright this is what I got, made it so that I get AFR read out around 700 to 1000 rpms
Rev smoother here, no ideal yet, but I don't care, I rather be able to fix my maps to get it to rev correctly.
Here is my msq and log of some data
Trying to take over, say 1200 rpms will result in a back fire, must be an area where the tune isn't near the other.
ANy thoughts appericated.
Rev smoother here, no ideal yet, but I don't care, I rather be able to fix my maps to get it to rev correctly.
Here is my msq and log of some data
Trying to take over, say 1200 rpms will result in a back fire, must be an area where the tune isn't near the other.
ANy thoughts appericated.
#93
Uploaded with ImageShack.us
=
WRONGGGGGGGGGGGGGGGGGGGG
After loading up diy autotune mspnp maps and thinking this **** should be good to go for 2 days, I finally decided to go back and relook over my crap
**** was wired wrong, time to fix and redo.
**** the rest of the tune related logs, this must of been the reason why, it should been idling by now.
#95
ok dokey Finally got 650rpm idle. I would like to get thoughts about my settings
Currently I am using reg_fuel at 19 and increased my ve bin area around 800rpms\50kpa to 97
afr's bounce around now still getting some pops from the exhaust, not sure why thats happening but anyways it seemed to me as you increase the ve bin it got better at idle, better as in smoother running but some point it pops than you go up tad more and it stops.
Here is the current tune and a datalog of letting idle and trying to rev it upwards at the end of the log.
Any thoughts? I"m still going though the stuff but now this is great, I have an idle finally, even though it still only at 650rpm
Currently I am using reg_fuel at 19 and increased my ve bin area around 800rpms\50kpa to 97
afr's bounce around now still getting some pops from the exhaust, not sure why thats happening but anyways it seemed to me as you increase the ve bin it got better at idle, better as in smoother running but some point it pops than you go up tad more and it stops.
Here is the current tune and a datalog of letting idle and trying to rev it upwards at the end of the log.
Any thoughts? I"m still going though the stuff but now this is great, I have an idle finally, even though it still only at 650rpm
Thread
Thread Starter
Forum
Replies
Last Post
stoves
Suspension, Brakes, Drivetrain
5
04-21-2016 03:00 PM