Trying to get started the RIGHT way
#1
Trying to get started the RIGHT way
Hello every Miata tuners!
I'm looking to get a STOCK miata 1990-1993 miata Basemap for my MS2 Extra 3.2.1
I Recently bought the Megasquirt from blean99. It was preloaded with His tune. Well i changed some setting for my car but i just feel im going no where..It start, Its running rough and cant get into a decend tune enought to drive it.
I would like to start from the begining with a stock map. In my opinion it would be a lot easier. Or if anybody could make a base map for a 1990 miata 1.6 engine with 440cc, stock cas, stock tps, Gm iat. Well just to start the car and be able to take it to my garage.
Thanks
I'm looking to get a STOCK miata 1990-1993 miata Basemap for my MS2 Extra 3.2.1
I Recently bought the Megasquirt from blean99. It was preloaded with His tune. Well i changed some setting for my car but i just feel im going no where..It start, Its running rough and cant get into a decend tune enought to drive it.
I would like to start from the begining with a stock map. In my opinion it would be a lot easier. Or if anybody could make a base map for a 1990 miata 1.6 engine with 440cc, stock cas, stock tps, Gm iat. Well just to start the car and be able to take it to my garage.
Thanks
#2
Download the MSPNP9093 basemap. Only difference will be the injectors which you can fudge with "Req Fuel."
Link: MegaSquirtPNP by DIYAutoTune.com
Link: MegaSquirtPNP by DIYAutoTune.com
#4
mmm there must be something i dont get...
when i open the file you told me to download i get this message
12 Warnings:
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:flexport equal to the proposed "PA0"
Warning: MSQ Units Mismatch for AFRTarget! Lambda found in current configuration, AFR found in MSQ, values were converted to Lambda based on Gasoline 14.7:1.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:spk_config_spka equal to the proposed "IGN1"
Warning: MSQ Units Mismatch for afrTable1! Lambda found in current configuration, AFR found in MSQ, values were converted to Lambda based on Gasoline 14.7:1.
Warning: MSQ Units Mismatch for afrTable2! Lambda found in current configuration, AFR found in MSQ, values were converted to Lambda based on Gasoline 14.7:1.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:rtbaroport equal to the proposed "SPAREADC"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:ego2port equal to the proposed "SPAREADC"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:boost_ctl_pins equal to the proposed "PA0"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:tacho_opt3f equal to the proposed "IGN"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:launch_opt_pins equal to the proposed "FLEX"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins2 equal to the proposed "PT7+6"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins equal to the proposed "Flex"
when i open the file you told me to download i get this message
12 Warnings:
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:flexport equal to the proposed "PA0"
Warning: MSQ Units Mismatch for AFRTarget! Lambda found in current configuration, AFR found in MSQ, values were converted to Lambda based on Gasoline 14.7:1.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:spk_config_spka equal to the proposed "IGN1"
Warning: MSQ Units Mismatch for afrTable1! Lambda found in current configuration, AFR found in MSQ, values were converted to Lambda based on Gasoline 14.7:1.
Warning: MSQ Units Mismatch for afrTable2! Lambda found in current configuration, AFR found in MSQ, values were converted to Lambda based on Gasoline 14.7:1.
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:rtbaroport equal to the proposed "SPAREADC"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:ego2port equal to the proposed "SPAREADC"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:boost_ctl_pins equal to the proposed "PA0"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:tacho_opt3f equal to the proposed "IGN"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:launch_opt_pins equal to the proposed "FLEX"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins2 equal to the proposed "PT7+6"
Warning: Parameter in .msq, but not valid for current firmware: No options found for Bit EcuParameter:N2Oopt_pins equal to the proposed "Flex"
#5
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,501
Total Cats: 4,079
NOOOOOOOOOOOOOOOOOOOOOOOOO
don't put a MSI map on your MS2.
you should have left his tune on it. it was based around that particular MS2 and all the inputs and outputs match how it was built.
Hornetball ball gave you AWFUL advice and I hope you saved a copy of the tune that was loaded. All you should have done was tweak a few parameters to match your injectors.
You have a custom build, ms2, by yours truly. Dont load MSPNP MS1 maps, MSPNP2 MS2 maps, DIYPNP MS2 maps, MS3 maps, or any other maps. please tell me you saved a copy of the loaded tune...
don't put a MSI map on your MS2.
you should have left his tune on it. it was based around that particular MS2 and all the inputs and outputs match how it was built.
Hornetball ball gave you AWFUL advice and I hope you saved a copy of the tune that was loaded. All you should have done was tweak a few parameters to match your injectors.
You have a custom build, ms2, by yours truly. Dont load MSPNP MS1 maps, MSPNP2 MS2 maps, DIYPNP MS2 maps, MS3 maps, or any other maps. please tell me you saved a copy of the loaded tune...
#7
NOOOOOOOOOOOOOOOOOOOOOOOOO
don't put a MSI map on your MS2.
you should have left his tune on it. it was based around that particular MS2 and all the inputs and outputs match how it was built.
Hornetball ball gave you AWFUL advice and I hope you saved a copy of the tune that was loaded. All you should have done was tweak a few parameters to match your injectors.
You have a custom build, ms2, by yours truly. Dont load MSPNP MS1 maps, MSPNP2 MS2 maps, DIYPNP MS2 maps, MS3 maps, or any other maps. please tell me you saved a copy of the loaded tune...
don't put a MSI map on your MS2.
you should have left his tune on it. it was based around that particular MS2 and all the inputs and outputs match how it was built.
Hornetball ball gave you AWFUL advice and I hope you saved a copy of the tune that was loaded. All you should have done was tweak a few parameters to match your injectors.
You have a custom build, ms2, by yours truly. Dont load MSPNP MS1 maps, MSPNP2 MS2 maps, DIYPNP MS2 maps, MS3 maps, or any other maps. please tell me you saved a copy of the loaded tune...
Yes i saved it!! but still now no cluster tach whatever i do!
I attach the tune inside the Ms when I had it! this one is untouched! If anybody could set it right to me for 440cc, Stock TPS, Stock MS map, no AFM, And stock CAS. It would be amazing to be able to at least start the car and drive under 3000rpm to bring it to my garage to work on it! cuz now my neighboors plan on killing me.
#8
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,501
Total Cats: 4,079
regain the tach but putting a 1K resistor in the diagnostics box between IG- and B+. If if doesn't work with the Stock ECU now, then the ignition settings of the MS were changed from how it was built and the ignitor is burnt up.
#9
Ok well i decided to go back with stock ECU for testing purposed, the car doesnt even as it was starting before. I checked spark plug for spark and i got no spark at all.
1- So if i understand correctly my ignitor is burnt up??
2- Will this have caused damaged to my megasquirt?
3- What should i do to Avoid this again?
4- Anybody Qualified for that. How much for a WORKING basemap, i'm just pissed, i dont want to run around all the summer, I work alot and i dont have much spare time
#16
Download the MSPNP9093 basemap. Only difference will be the injectors which you can fudge with "Req Fuel."
Link: MegaSquirtPNP by DIYAutoTune.com
Link: MegaSquirtPNP by DIYAutoTune.com
Steven: From what you described, all you needed to do was change your fuel VE maps or tweak injector settings (And I will remind you, I did specifically tell you this in PMs!!!!), not....I hope you the best of luck man, that was truly bad advice from Hornetball.
Re-flash to your previous tune ASAP, and copy fuel maps from other basemaps if you have to, but don't flash to random tunes in the future!
#17
Dude, -epically- bad advice.
Steven: From what you described, all you needed to do was change your fuel VE maps or tweak injector settings (And I will remind you, I did specifically tell you this in PMs!!!!), not....I hope you the best of luck man, that was truly bad advice from Hornetball.
Re-flash to your previous tune ASAP, and copy fuel maps from other basemaps if you have to, but don't flash to random tunes in the future!
Steven: From what you described, all you needed to do was change your fuel VE maps or tweak injector settings (And I will remind you, I did specifically tell you this in PMs!!!!), not....I hope you the best of luck man, that was truly bad advice from Hornetball.
Re-flash to your previous tune ASAP, and copy fuel maps from other basemaps if you have to, but don't flash to random tunes in the future!
Well i hope i didnt screw my megasquirt . Ill let you guy know tomorrow if my car start at least on the stock ECU
#20
Boost Pope
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,052
Total Cats: 6,615
I'm not sure why we even bother. The sun is going to go nova in 4 billion years anyway, and when that happens, it won't really matter whether you have an analog TPS or not, will it?
It's all pointless. Just boil the oceans and get it over with.
It's all pointless. Just boil the oceans and get it over with.