1990-2005 MS3x, DIYPNP, And MS3Module PNP Assembly!!
#661
MS3Pro Module PNP - can you make this for a 99? I'll be buying a mspnp this winter.
#663
Elite Member
iTrader: (2)
Join Date: Aug 2016
Location: New Fucking Jersey
Posts: 3,890
Total Cats: 143
Your OP leaves out 99-00 from the new offerings.
For those in the cheap seats, would you care to elaborate at all on what the added benefits are vs the MS3X?
I see internal datalogging, sequential spark, traction control (for ABS cars?), better MAP sensor, stock knock module (?), water injection and/or 5th injector setup (8 inj banks), better table switching, launch control... and?
For those in the cheap seats, would you care to elaborate at all on what the added benefits are vs the MS3X?
I see internal datalogging, sequential spark, traction control (for ABS cars?), better MAP sensor, stock knock module (?), water injection and/or 5th injector setup (8 inj banks), better table switching, launch control... and?
#664
Boost Czar
Thread Starter
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
whoops. should be 99-05. thanks.
Benefits:
So until I come up with a better solution, there will be be some wires coming directly off the board (like for wbo2 12v, ground, signal) for all other units -- which i still have to do on my current 96-05 ms3x builds.
Benefits:
- An OTS, stamped, ECU--not hand-populated and soldered--with integrated RTC and Knock modules. It is essentially the same board used in the MS3 Pro.
- An OTS, printed adapter-board which allows the omission of a hand-built/soldered patch harness that could lead to errors/failure.
- The adapter board is populated with the required circuits to run a miata, as well as additional popular circuits for customization:
- constant barometric corrections
- additional analog and digital inputs
- bluetooth module
- wifi module
- alternator circuit -- if you dont wanna use the software to control it
- alternator charge light circuit -- if youre out of outputs to waste on this
- Speeduino VR conditioner
- (4) additional VR conditioners -- these can be used to add traction control
- EGT circuit
- TinyIOX circuit -- for additional sensor inputs via CAN
- Active low circuits
- Accelometer circuit
- Installs within the OE ECU case (requires some cutting/drilling the case) for easier installs -- no zip ties needed for NBs.
- Should take considerably less time to assemble/deliver.
So until I come up with a better solution, there will be be some wires coming directly off the board (like for wbo2 12v, ground, signal) for all other units -- which i still have to do on my current 96-05 ms3x builds.
Last edited by Braineack; 09-15-2018 at 11:36 AM.
#665
Elite Member
iTrader: (2)
Join Date: Aug 2016
Location: New Fucking Jersey
Posts: 3,890
Total Cats: 143
Oh that sounds awesome.
Re: Zip ties for the ECU. I drilled holes in the singular bracket and have my MS3X mounted in the stock-ish location. I did use zipties to put the ecu on the bracket because I didn't have the right sized bolts lol.
As an aside, the base MAP sensor on the MS3X is 2.5 bar vs 4 bar for the MS3 Pro, correct? That's also a factor for anyone considering things. 2.5 bar is dandy for a stock motor, the second you build it you're going to want something that goes higher.
Re: Zip ties for the ECU. I drilled holes in the singular bracket and have my MS3X mounted in the stock-ish location. I did use zipties to put the ecu on the bracket because I didn't have the right sized bolts lol.
As an aside, the base MAP sensor on the MS3X is 2.5 bar vs 4 bar for the MS3 Pro, correct? That's also a factor for anyone considering things. 2.5 bar is dandy for a stock motor, the second you build it you're going to want something that goes higher.
Last edited by ridethecliche; 09-17-2018 at 01:52 AM.
#666
Boost Czar
Thread Starter
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,499
Total Cats: 4,080
For these, it's still a 2.5bar as default -- that's ~22psi.
I can offer them with a 4bar, but it will change the cost a little; not much. Or you could use the GM 3bar and install it remotely inside the engine bay.
The MS3 module has no map sensor on it.
I can offer them with a 4bar, but it will change the cost a little; not much. Or you could use the GM 3bar and install it remotely inside the engine bay.
The MS3 module has no map sensor on it.
#667
Elite Member
iTrader: (2)
Join Date: Aug 2016
Location: New Fucking Jersey
Posts: 3,890
Total Cats: 143
I guess offering the 4 bar would be helpful unless you think the resolution is crap. 22 PSI limit means that's where overboost should be set, so realistically you're looking at a MAP of 235-240 tops so you have a bit of wiggle room for overboost protection. That leaves you at about 20psi. Still plenty, but you always end up wanting more lol.
#668
I pmed you let me know if you don't get it ill send again
#672
Forgive what may be glaring oversight, but what are the 3 wires sticking out of the ms3pnp board? A remote friend is helping wrap up my install in my '90 1.6 car, and we cant find the documentation indicating what the red, black, and yellow/red wire go to. It's not shown in any of the online install guides
Thanks!
Thanks!
Last edited by rustrocket; 12-20-2018 at 11:25 AM.
#674
#675
Can I place an order, what’s the wait time for everything ?
#677
#678