EPIC nuts/studs loosening thread (reposting stupid stuff without reading = warning)
#941
Elite Member
iTrader: (2)
Join Date: Jan 2007
Location: Los Angeles, CA
Posts: 8,682
Total Cats: 130
Has anyone tried OEM Nissan RB26DETT turbo studs?
Reason I ask....
I've been in the Skyline tuning scene for a number of years. Back in 2008 I built a RB26 with a friend of mine for his R32. Fully forged internals, pro-cams, p/p heat etc etc. We were running twin GT2860r-5's and ran OEM Nissan studs. They are M10x1.25. We had the car tuned by Eric @ XS Engineering and it made 580AWHP @ 1.8BAR. Never had any issues with turbo studs on the dyno or at the multiple track days he ran after the fact. Yes, I know not "real racing" but it's the only experience I have with it.
After doing a bit of research, apparently they are M10x1.25 Inconel studs and IIRC they run around $8/ea.
I'm thinking I may try these out and see how it goes. No harm in trying since my manifold is m8 right now and I can drill/tap them out to m10 easily. But instead of going 1.5 like many people here its 1.25 (wich over the past few days I've found VERY hard to find quality studs for... even ARP do sent make anything according to the rep I spoke with on the phone.)
Reason I ask....
I've been in the Skyline tuning scene for a number of years. Back in 2008 I built a RB26 with a friend of mine for his R32. Fully forged internals, pro-cams, p/p heat etc etc. We were running twin GT2860r-5's and ran OEM Nissan studs. They are M10x1.25. We had the car tuned by Eric @ XS Engineering and it made 580AWHP @ 1.8BAR. Never had any issues with turbo studs on the dyno or at the multiple track days he ran after the fact. Yes, I know not "real racing" but it's the only experience I have with it.
After doing a bit of research, apparently they are M10x1.25 Inconel studs and IIRC they run around $8/ea.
I'm thinking I may try these out and see how it goes. No harm in trying since my manifold is m8 right now and I can drill/tap them out to m10 easily. But instead of going 1.5 like many people here its 1.25 (wich over the past few days I've found VERY hard to find quality studs for... even ARP do sent make anything according to the rep I spoke with on the phone.)
#942
Seems to be some REAL progress. Here's a state of the nation of this thread:
- spookyfish's success with 304 SS M10 studs
- Inconel's initial success
- Suggestions of Rene41
- $8 Skyline M10x1.25 Inconel studs
- kverges' awesome enduro success with A286 3/8" bolts
(I can't believe I missed the above discussion)
Stupid Q time: why might Nissan use 1.25 threads instead of 1.5?
- spookyfish's success with 304 SS M10 studs
- Inconel's initial success
- Suggestions of Rene41
- $8 Skyline M10x1.25 Inconel studs
- kverges' awesome enduro success with A286 3/8" bolts
(I can't believe I missed the above discussion)
Stupid Q time: why might Nissan use 1.25 threads instead of 1.5?
Last edited by JasonC SBB; 02-12-2010 at 11:46 AM.
#944
apparently most Japanese studs are 1.25. They seem to like the fine thread. Miata head -> manifold is 1.25 as well. Nissan KA and SR engines also use them.
My manifold right now has 3 m8x1.25 and 1 m10x1.5 stud since I stripped one out. It's currently getting helicoiled so I can run a M10x1.25.
My manifold right now has 3 m8x1.25 and 1 m10x1.5 stud since I stripped one out. It's currently getting helicoiled so I can run a M10x1.25.
#945
the finer 1.25 thread would require more rotation to remove than a 1.5 thread. It would also have to rotate further before becoming 'lose' than a 1.5 thread would.
The more likely reason for a major automobile manufacturer to use 1.25 studs instead of 1.5 studs is because that's what was available/cheapest at the time.
Alternatively, they may have used 1.25 studs if the walls of the manifold were thin. I believe the smaller pitch bolt has a smaller outside diameter than the larger pitch bolt. Even so, we're probably talking about only a couple thousandths though, and Nissan likely wouldn't have made a part with those properties.
The more likely reason for a major automobile manufacturer to use 1.25 studs instead of 1.5 studs is because that's what was available/cheapest at the time.
Alternatively, they may have used 1.25 studs if the walls of the manifold were thin. I believe the smaller pitch bolt has a smaller outside diameter than the larger pitch bolt. Even so, we're probably talking about only a couple thousandths though, and Nissan likely wouldn't have made a part with those properties.
#950
Tour de Franzia
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
Your brakes are going in tomorrow.
#952
Elite Member
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
Since the thread has been resurrected I'll check in. Still nothing to report on my through-bolted tube manifold setup (pictures earlier in the thread). I've been slow to get the engine back in the car. But, since I am preparing a different Miata for the track, and I am tired of pulling this engine, my fastener test may never meet the track test condition requirement anyway.
So I'll report back if it ever does loosen or leak, but if it does not fail it is not proof of being a track worthy solution. A necessary but not sufficient test as we engineers say.
So I'll report back if it ever does loosen or leak, but if it does not fail it is not proof of being a track worthy solution. A necessary but not sufficient test as we engineers say.
#957
Elite Member
iTrader: (15)
Join Date: Sep 2007
Location: Incline Village, NV
Posts: 2,034
Total Cats: 5
Being fast is a main issue as well. Mike (picture above) has put a fair amount of track time on that setup without issues. IIRC 5-6 track days. Now that he turned the boost up to 15psi his nuts are loosening.
#960
Yes. That's the only place I put resbond. As Savington said, the nuts were on there just tight enough to get the turbo to seal against the manifold which has been working great at 12 psi. I tuned it for 15 psi this weekend which lasted only the first (slow) session at the track. The top/front nut spun freely when I tried to tighten it right after the last session. All of the nuts were loose.
I need to figure out what to replace the studs/nuts with before April 10/11th. V-Band isn't an option . . . yet.
I need to figure out what to replace the studs/nuts with before April 10/11th. V-Band isn't an option . . . yet.