New Tuner Studio version with VEanalyze live
#24
Oh my gawd!
I was prompted by TS and installed the update today at work on my laptop, I didn't even see the new feature "VE Analyser live"
Another nice addition that I noticed was that any cell changes you make to your VE table holds the "red" and "blue" colours and notes previous values even after closing the table and re-opening it/switching 3D view etc. The old version used to lock the live trail after importing a modified VE table from MLV which meant you were forced to close the table and re-open it if you wanted to watch the live trail as you drive.
I did spot another issue too, I made changes by interpreting MLV data while offline and modifying my MSQ by hand in TS while offline and saving it to my usual folder. When connecting the laptop to my MS and connecting successfully, there was no 'settings change report' prompt? It confused me for second, so I had to manually load my MSQ in while my MS was online.
I'll try this new feature tomorrow for sure! I'm very excited about it if it does what it says on the tin!
I was prompted by TS and installed the update today at work on my laptop, I didn't even see the new feature "VE Analyser live"
Another nice addition that I noticed was that any cell changes you make to your VE table holds the "red" and "blue" colours and notes previous values even after closing the table and re-opening it/switching 3D view etc. The old version used to lock the live trail after importing a modified VE table from MLV which meant you were forced to close the table and re-open it if you wanted to watch the live trail as you drive.
I did spot another issue too, I made changes by interpreting MLV data while offline and modifying my MSQ by hand in TS while offline and saving it to my usual folder. When connecting the laptop to my MS and connecting successfully, there was no 'settings change report' prompt? It confused me for second, so I had to manually load my MSQ in while my MS was online.
I'll try this new feature tomorrow for sure! I'm very excited about it if it does what it says on the tin!
Last edited by CRAIGO; 01-14-2010 at 06:41 PM.
#29
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,201
Total Cats: 1,138
My setup (.ini) files were different. So I had to change the afr gauge settings to read AFR instead of volts again. Other than that the menus are nearly identical. I think the nicest part was the gauges working behind the menus, and the little icons in the drop down menus. I always had to read every entry to find the AFR target table, now I know exactly where it is, it's the only table under "more settings"
My batteries dead, so I can only rev away at a stop with the laptop plugged in, but I'm going to go try this now, I'll report back in a few minutes.
My batteries dead, so I can only rev away at a stop with the laptop plugged in, but I'm going to go try this now, I'll report back in a few minutes.
#30
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,201
Total Cats: 1,138
Well there it is. I can't get it to change anything, even with the resistance set to easy. As I said I can only rev it since my laptop battery is dead, and I'm unboosted since my 440's are out for cleaning, but at least this shows you what it looks like. The only time it wants to change something is when I floor the throttle, at which point it filters the log due to a "accel flag", whatever that means. Pretty simple though, me likely.
#34
Well there it is. I can't get it to change anything, even with the resistance set to easy. As I said I can only rev it since my laptop battery is dead, and I'm unboosted since my 440's are out for cleaning, but at least this shows you what it looks like. The only time it wants to change something is when I floor the throttle, at which point it filters the log due to a "accel flag", whatever that means. Pretty simple though, me likely.
#36
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,201
Total Cats: 1,138
Down below where it says "active filter:", it's blank. I had it up at 160 but I didn't want to wait that long, it says "active filter: min clt". No warnings like MLV saying that 100% of the log was ignored because of settings.