poobs

iTrader: (1)

From the AFR table

Rouphis

The 6x6 one in megasquirt? Or the 12X12 one in MLV. In ether case, it is nowhere near correct. In both tables my 101KPa target is 13.0 yet VE Live is trying to make 14.7.

-Rouphis

CRAIGO

It will target whichever table YOU tell it to target. By the way the AFR target table in TS or MT is an 8x8 table.
Do yourself a favour and stick with AFR target table 1 (the 8x8) It's all interpolated so you'll have no gains by having more cells to enter "14.7" in or "12:1" for boost etc.

MLV can be told to base it's analysis on whichever table you tell it to look at.You have an option of three tables IIRC.

Rouphis

I know about MLV, MLV is fine. But in TS VE Live, its not interpolating correctly.

Zaphod

Strange, you would be the first to have this problem.

Is your wideband sending the correct values? Are you seeing the same values in TS and on your WB gauge?

Rouphis

My wideband is fine. And VE analyze in MVL works fine. I will post my .msq in a little while.

-Rouphis

poobs

iTrader: (1)

Ok, I think I understand what the delay does but how do I determine what to set it to ?

Maybe I'll just leave it alone but again if something seems wrong how do I know if it is these settings that are at fault ?

flipt86

iTrader: (4)

Ok guru's... If I load my current msq in megatune like I have been for the past year and a half, the car runs as good as it ever has.
BUT... If I load the same msq using TS it runs like ****. Completely lean idle around 17 to 1, leans out to 18/19 to 1 while free revving the car in neutral. Didn't even try to drive the car as it was running horribly. The ve map is the same in both TS and Megatune, as are all other settings that I can see.
I can't figure this out, any advice would be appreciated. Why the difference?

Mach929

iTrader: (3)

have you setup a project in ts properly?

southernmx5

iTrader: (1)

Did you choose the right firmware and set your wideband for your project in TS? Also make sure airden, matfactor, and thermfactor are in the project inc folder.

flipt86

iTrader: (4)

Followed the directions in the other thread to the best of my knowledge, hires firmware set, all three inc files are in project inc folder, innovate wideband default selected... I'll look again. Keep the tips coming, this is really frustrating me.

popopopop

Is your afr the same in TS? I didn't know people ran the default LC1 settings.

flipt86

iTrader: (4)

yes they are the same, I run them on purpose after having a long talk with diy.

poobs

iTrader: (1)

Is there a case/condition when you don't have to copy those files to your project folder ????

I'm using TS and MT interchangeably and I'm not having the above problems. !!!

jrw

iTrader: (4)

super noob question...

whenever I use VE live it is targeting WAAAAAAY too rich, cruising in 5th I'm getting in the mid 9's.

I realize this is probably all my fault, I just need to know how to correct it. should I reset-up my LC-1, maybe I have the settings incorrect???

popopopop

The VE live uses your AFR table as its target, check that.

jrw

iTrader: (4)

go to ve analyze live > advanced options > AFR targets?

Braineack

iTrader: (62)

well that explains why it's hitting 9s... rofl

try a table like this:

Zaphod

@jrw - the AFR table in VEanalyze should be the same as your normal AFRtable for VEtable1. It uses the same table.

CRAIGO

JRW, that table looks like a classic case of table corruption. I had a few of those when starting out with MS and TS.

Use Brains and see what happens