How (and why) to Ramble on your goat sideways
It has straight lines, or is supposed to. I guess I should have said consistently round.
Reply
0
0
Reply
0
0
when I use those dremel cutting bits, I always get dissapointed by the same results... until I started putting the dremel into a vice and moving the object that needs cutting. Someday I will invest or make a dremel-holding milling table.
Reply
0
0
Reply
0
0
Joined: Jun 2005
Posts: 19,338
Total Cats: 574
From: Fake Virginia
dremel in a vise is the way to go for sure.
also cut that on a jig or band saw. maybe consider drilling the center with a large diameter hole saw before cutting it out of the sheet.
also cut that on a jig or band saw. maybe consider drilling the center with a large diameter hole saw before cutting it out of the sheet.
Reply
0
0
Reply
0
0
I <3 my jigsaw. It's got some old magic blade stuck in it that I've cut ABS, aluminum, stainless and whatever you can think of with ease.
Also, since my bitching about the hotness over here lately, it's cooled down significantly and been raining like whoa. Oh the ironing
Also, since my bitching about the hotness over here lately, it's cooled down significantly and been raining like whoa. Oh the ironing
Reply
0
0
Reply
0
0
From Pirate 4x4 forum
.
So was this one of you sadists?
When I lived in Phoenix I was driving in rural Pinal County on my way to do an appraisal and found this dude kneeling down on the shoulder next to his little mazda miata....
I slowed down and stopped next to him...
And saw him attempting to cut the head and horns off a goat! Not sure if it was a mountain or billy goat but I was not about to hang around to see if he needed help.
Dude was covered in blood and looked like one crazy SOB!
I was training this chick to be an appraiser and she totally freaked out and quit a week later
I slowed down and stopped next to him...
And saw him attempting to cut the head and horns off a goat! Not sure if it was a mountain or billy goat but I was not about to hang around to see if he needed help.
Dude was covered in blood and looked like one crazy SOB!
I was training this chick to be an appraiser and she totally freaked out and quit a week later
So was this one of you sadists?
Reply
0
0
Quick question. I'm having my manifold drilled for 10mm studs; should I go 10x1.25 or 10x1.5 ?
Quick googlin' tells me that 10x1.5 is more common. I'd like to hear your thoughts (yes, you!) on it.
Quick googlin' tells me that 10x1.5 is more common. I'd like to hear your thoughts (yes, you!) on it.
Reply
0
0
Joined: Sep 2005
Posts: 34,402
Total Cats: 7,523
From: Chicago. (The less-murder part.)
The torque specs are typically slightly higher for fine-pitch fasteners, meaning they will offer slightly greater clamping force as opposed to coarse-thread fasteners.
Coarse-thread fasteners are more commonly available, and are less likely to become stripped / galled during the removal process.
Coarse-thread fasteners are more commonly available, and are less likely to become stripped / galled during the removal process.
Reply
0
0
This connector, what it do? Came from the big loom on the passenger side and used to run in front of the motor with the wires for the IAC, TPS and PS. Was this for the aircon?
D0D1D253-1150-4FD5-8DC2-21D0320ED638-9419-0000056DF57B0F6B.jpg?t=1375279079
Started labeling/unwrapping everything to prepare for VVT goodness, but this one doesn't look familiar though.
D0D1D253-1150-4FD5-8DC2-21D0320ED638-9419-0000056DF57B0F6B.jpg?t=1375279079
Started labeling/unwrapping everything to prepare for VVT goodness, but this one doesn't look familiar though.
Reply
0
0
Thought I already found 2 or 3 of those. What does it purge, fuel fumes too?
Edit: it's the solenoid on the fuel rail no?
Do I still need this with the VVT motor and 99 fuel rail?
Edit: it's the solenoid on the fuel rail no?
Do I still need this with the VVT motor and 99 fuel rail?
Last edited by Oscar; Jul 31, 2013 at 12:10 PM.
Reply
0
0
yeah, it does something under certain conditions to help with starting, just changes the vacuum to the fuel pressure regulator.
I used it to control VICS on the last car i fooled with.
are you converting to returnless?
I used it to control VICS on the last car i fooled with.
are you converting to returnless?
Reply
0
0
