First MegaSquirt 3 datalog and msq
#22
mkturbo.com
Thread Starter
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
My tip in settings are definitely off right now. Here is a datalog of me idling and just hitting the gas. I will be doing some reading about tip in settings tomorrow but if anyone wants to take a look and give me some pointers it would be greatly appreciated.
#24
mkturbo.com
Thread Starter
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
It will happen in the future. Got a lot or other things these next couple of weekends. 6 speed goes in this weekend and then easter the following weekend. So maybe the weekend after that I will figure out what all needs to be done to get sequential going.
#25
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Quite probable.
Your VE table probably isn't dialed in yet. No use in playing with enrichments until after the VE table is nailed.
My tip in settings are definitely off right now. Here is a datalog of me idling and just hitting the gas. I will be doing some reading about tip in settings tomorrow but if anyone wants to take a look and give me some pointers it would be greatly appreciated.
#26
mkturbo.com
Thread Starter
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,177
Total Cats: 1,681
Now onto the negatives. Tonight as I was going out to my friends house I started having problems with my MS3. My tach started falling randomly and it felt like I was not getting spark. It got so bad that if i came to a stop my car would almost stall out. Giving it gas in any gear would do do next to nothing and it was hard top get above 2500rpms. Unfortunately my laptop battery was dead so I did not get a log of it. I plan on trying again in the morning and will see what happens.
#30
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
I suppose if there were enough demand demonstrated, we could discuss it, but there are no current plans to do so that I'm aware of.
Which PNP do you own, the MSPNP (in the white box)? We have not seriously attempted to convert a MSPNP to the MS3 processor. I know I posted that pic a few posts ago, and I'm sorry if it was confusing, but all I did was drop a (not fully functional, pre-release) MS3 processor into a MSPNP case to see if it would physically fit. And it does, sort of--it needs the side of the case is clearanced for the MS3's USB port.
Since the MSPNP is at its heart a v3.57 board, then yes it should be possible to upgrade it to MS3, but due to lack of time and product availability, we've not actually tried it. Should be a matter of plugging it in, changing some jumpers around, and fixing up a basemap. We're out of MS3 cards, and what I've heard through the grapevine is that it will be ~2 months before we see any more.
Which PNP do you own, the MSPNP (in the white box)? We have not seriously attempted to convert a MSPNP to the MS3 processor. I know I posted that pic a few posts ago, and I'm sorry if it was confusing, but all I did was drop a (not fully functional, pre-release) MS3 processor into a MSPNP case to see if it would physically fit. And it does, sort of--it needs the side of the case is clearanced for the MS3's USB port.
Since the MSPNP is at its heart a v3.57 board, then yes it should be possible to upgrade it to MS3, but due to lack of time and product availability, we've not actually tried it. Should be a matter of plugging it in, changing some jumpers around, and fixing up a basemap. We're out of MS3 cards, and what I've heard through the grapevine is that it will be ~2 months before we see any more.
#31
Sure, but if you can't set a period prior to spark time per cylinder then its a waste of time. Real knock detection would make MS so much more attractive...but I'm not sure that I'm willing to put any effort into it. I've already demonstrated with lap times that I have my hands full at 250whp.
Ken
#34
You man using it as a true ADC instead of just an on-off digital signal I assume.
I think you can do that now as long as you're not trying to let the MS actually use the knock signal at the same time... You can just log the generic ADC input right now.
Was there something more that you wanted?
I see that request as more or less unrelated to the knock windowing feature.
Ken
I think you can do that now as long as you're not trying to let the MS actually use the knock signal at the same time... You can just log the generic ADC input right now.
Was there something more that you wanted?
I see that request as more or less unrelated to the knock windowing feature.
Ken
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
Johnny Tater
MSPNP
1
09-27-2015 12:38 AM