Curly's boring mt.net circle of life completion (Turbo->N/A conversion)
#44
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,204
Total Cats: 1,138
http://www.ebay.com/itm/New-Design-T...item3f0441846f
I bought it mostly for its actuator bracket location now I just need to find out how to turn down the boost.
I bought it mostly for its actuator bracket location now I just need to find out how to turn down the boost.
Last edited by curly; 02-09-2012 at 08:00 PM.
#46
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,204
Total Cats: 1,138
Link to thread?
Now I just need to decide on an intercooler routing. For some reason I though Sav had a simple through the fender setup, but he's headlightless. Then I found johnathewha's setup, but he's running some stupid narrow radiator. I'm hopping I can fit two 180* pieces around the radiator to hook up with the intercooler. Then 2 90* pieces on each to hook it into compressor and throttle body.
Now I just need to decide on an intercooler routing. For some reason I though Sav had a simple through the fender setup, but he's headlightless. Then I found johnathewha's setup, but he's running some stupid narrow radiator. I'm hopping I can fit two 180* pieces around the radiator to hook up with the intercooler. Then 2 90* pieces on each to hook it into compressor and throttle body.
#47
that one looks pretty good, really. and yep, pretty much a GT2560, which is probably about perfect for stock motor.
Is the wastegate actuator even attached to the compressor housing at all? if not, that's really cool, would allow guys to pretty much point the compressor in whatever way they wanted and retain the IWG. Hopefully its not really 14 psi..... maybe with some wastegate porting it will be just fine. Worst case it looks like you could fit about any other generic straight one on there with a lower rating.
Is the wastegate actuator even attached to the compressor housing at all? if not, that's really cool, would allow guys to pretty much point the compressor in whatever way they wanted and retain the IWG. Hopefully its not really 14 psi..... maybe with some wastegate porting it will be just fine. Worst case it looks like you could fit about any other generic straight one on there with a lower rating.
#48
Link to thread?
Now I just need to decide on an intercooler routing. For some reason I though Sav had a simple through the fender setup, but he's headlightless. Then I found johnathewha's setup, but he's running some stupid narrow radiator. I'm hopping I can fit two 180* pieces around the radiator to hook up with the intercooler. Then 2 90* pieces on each to hook it into compressor and throttle body.
Now I just need to decide on an intercooler routing. For some reason I though Sav had a simple through the fender setup, but he's headlightless. Then I found johnathewha's setup, but he's running some stupid narrow radiator. I'm hopping I can fit two 180* pieces around the radiator to hook up with the intercooler. Then 2 90* pieces on each to hook it into compressor and throttle body.
#51
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,204
Total Cats: 1,138
It was just picked up in CA to be delivered to tx. Abe's going to hate me, I might be asking for update pictures every day.
We'll see about wanting more. As is I'll be maxing my injectors and at the limit of my stock internals.
We'll see about wanting more. As is I'll be maxing my injectors and at the limit of my stock internals.
#55
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,204
Total Cats: 1,138
I started working on my intercooler setup, so far I'm happy. My over the radiator setup always bugged me. Bashed pipes for hood clearance, difficult to seal the ducting, and near impossible to do anything with a filter beyond bolting it right to the turbo.
Old:
And a rough mock up of the new hot side with old pipes:
Cold side. The first straight coupler after the TB won't be there, I just didn't have a piece long enough for mock up:
The 90* piece will be a 2-2.5" piece I have, with a 2.5" pipe going into one of these at the intercooler:
Should provide for a fairly clean setup. Best part about all of this is I'm keeping the same number of couplers (x3 per side) as my over the radiator setup. Not bad.
Worst part is this, which is definitely going to affect resale value. Notice the crack on the top weld:
#59
Cpt. Slow
Thread Starter
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,204
Total Cats: 1,138
Did he get my turbo already? Nice. And you're welcome. I'm hoping my banjo bolt fits the oil feed, I have a drain fitting somewhere around here, and I'll be using clamped on hoses for the time being.
Did he say what sizes all four are?
Did he say what sizes all four are?